Tarball

Big Picture lesson.... Choose your roommates wisely!

I am curious about this also for a slightly larger enclosure

epoxy the broken plastic back in place and hope for the best.

Just curious, what is your peak frequency on that setup ?

Here is one option for image hosting: Image Shack So you would upload the image to a hosting site Copy the web address of the link after it is uploaded In the post editor click the "insert Image" link In the "Url" field post the web address to the link As to the glass ...not my area of expertise...yet **Edited to add a few details about getting the link to the forum

naahhh,,i just thought that bass in giving you cancer its just stupid how can shakiness give you cancer? perhaps being in close proximity to high strength electro magnetic fields ... Linkage

have you done Big 3 ?

Is that $200 each or for both? I read that as $200 + Shipping for the pair but only "CoolWazabi" knows for sure. /cheers

Ported. But you probably won't reach obnoxious with this setup...maybe a just little rude Look around these forums a bit and you will see what obnoxios can be...maybe even some ludacris and perhaps 1 or 2 plaid!

Swap back to the 16 gauge and see if the problem goes away.

Triple post....cleaning up.... move along....move along...

Triple post....cleaning up....nothing to see here.

ahhh the smell of ozone....brings back memories....

Although Im sure pleanty will disagree; since this is your first I recommend sealed. Especially with the 25hz Fs on the P1s You'll get nice deep flat response. The box will be simpler to build and will be a greta overall experience all the same. With a ported box you will enjoy a nice increase at the tuned frequency, at the cost of a slightly more complex box and you'll miss out on the low lows that you can't hear anyway . /cheers

Yeah, either the box is too large, the subsonic filter needs adjusting and/or your exceeded the physical limits of the sub (1 or both) and they are damaged. My noob 2cents

This. I'd not recommend doing a box like that...just too risky depending on how small the cut-through is going to be compared to the normal size of the box. Yeah I agree with both of you it is risky. The cut through is going to have to be huge to compensate for the short height of the bed. I would be using every inch I can squeeze out of it leaving enough room to glass and attach to the body... Unless I can spec out a good 4th order BP in {16" X 39" X 60"} which will be tight with the 15.5 dia of the sub. I may be able to shave a bit off by removing the gasket though...and notch out a section in the top and bottom of the box. I would think that you're probably best off with a bp, the angle probably wouldn't matter really, it should be fine :-) How big is the hole you are going to cut be? I have a nice idea for how to do the box. Hole can be as big as it needs to be. Just to guesstimate a max...36" X 14" ...ish

This. I'd not recommend doing a box like that...just too risky depending on how small the cut-through is going to be compared to the normal size of the box. Yeah I agree with both of you it is risky. The cut through is going to have to be huge to compensate for the short height of the bed. I would be using every inch I can squeeze out of it leaving enough room to glass and attach to the body... Unless I can spec out a good 4th order BP in {16" X 39" X 60"} which will be tight with the 15.5 dia of the sub. I may be able to shave a bit off by removing the gasket though...and notch out a section in the top and bottom of the box.

Clicky[

Couple of pics...

Car = S10 ext cab (1998) Box: I'm thinking either large ported or bandpass if possible. One problem with bandpass (4th order) in this truck is the bed dimensions...only allows for 16" total box height so the subs would have to be angled...not sure if I wanna do that. If I go ported (leaning towards this) I plan on using the ext cab area to mount the subz...cut-through inside the box and additional box volume in the bed (yeah the cut-through will need special attention to be air tight). I wanna let the beasts breath! ported in the cab from the top of the box followed by 2 45degree angles into the bed. Something like this...

No username in the pic but its what I have immediately available.

Will Post an image tomorrow. I'll need to unbox them. I understand the request with my "2 Post" count As for the Amp. I have heard mixed opinions about it. It's what I have so I'm going to run with it for now.

OK, I have 2 15 MTs. All the specs I have are: Sub: Dual Progressive Spiders Flat Wound Coils Dual 1.4 ohm Dual Tinsel Leads Electrical (plan): 350 Amp SP AD244 (adjustable VR) Big wire throughout (1/0 or greater) Kenetic 16v/12V batts (3 or 4 will add more if needed) Amp: SS XXX4000d ( @ 16+V ) Will double after initial install and testing. I've tried emailing RE with no response... PORTED: I would like to know what kind of airspace these need. Looking to port Looowww like high 20's low 30's. Thinking 6" x 30" for port surface area then port length to the box for the target frequency. Thanks in advance for any help... /cheers