JR2011bu

Got this done already power wires are on left(driver) side and all signal lines running on right(pass) side. But thanks Alright well i hope so, dont want this thing to burn out on me, not easily available so can't just replace like that. Also i went back an tuned using track 7. After about 2 songs woofer started gettig smelly haha luckily i wasn't full tilt the whole time, i would turn th bass remote up at times then back down.. Putting this z v.3 to work.

So here is what is happening. When i tune my amp using the DD-1 (-10db track) before i reach distortion levels on my gain i hear a buzz from the amp. Amp is a SHOK II sub is Sundown z10" v.3 and max level on HU is 50 distorts at 48 so i tune at 47. Its not my first time tuning amp with DD-1 just wondering if anyone has come across this buzz on a different amp. Any suggestions i'm all ears.

I have a z10" v.3 and i am running 2.5k on it and it loves it.. But i have seen those SA's take upwards of 2k each. But i will say this feed those monsters at your own discretion lol.. I would 1.2k to the SA's is a safe amount of power.. But Z's ha they will ask for more and more until they have had enough. And SQ is awesome.. Of course in theright enclosure with the right power those SA's will bang and they are more budget friendly as well..

http://www.teamnwspl.biz/t235-debadging-trim-and-side-moldings try going here and reading this article.. Some of the local guys have a DIY log and i found this there hope it helps..

SMH lol.. OP Just do what you think will please you. Folks here are just trying to help you out and prove there statements, sometimes it is said very directly but hey just knod your head say roger and move out no need to pout. After all in the end it will be your decision wether or not you take the advice or continue down your path. just my $.02

I'm reading through this post smh. I used to have a brz1700.1 on my 10"v3 and like quoted before "it was laughing at me" then got a bb2400.1 PA and still it was asking for more. Now I have a little beast SHOK II doing about 2500 at 1ohm to the z10" v3 and it looks happier. So if I were you I would just get the 15" v3 like I just did. And if you want more power drop it in just make sure you have a clean signal and your good.

Sorry guys haha. I wish I could share the wealth but for now this is mine haha.

Shipping a 90lb batt will be about the same as getting it online man lol but i hear you man. I wish i could have the whole lot that he is getting rid of lol I think he said 20 batts lol. But then you would need Shocker Hal's vovlo or something lol.

haha forgot to mention these are brand new in box i may be able to get more than 1 haha. My buddy is a mechanic and needs to clear a few of these from his area at work. But yes i will check the resting voltage and pop them in. man my Malibu is gonna look like i dropped the back with this weight though lol..

Yes sealed AGM Batt And it is free.

So I was talking to my buddy and he has one of thee bad boys available that I can have. Just wondering what you guys think. The battery is not this same brand but it's the same specs. http://www.wholesalebatteriesdirect.com/more-military-agm-batteries/66729-fgmx12120-battery-replaces-hawker-nsn-6140-01-485-1472.html The one he has is the same exact except it is an Armasafe batt. Would this be a good idea to put in trunk I will soon be buying either a mechman 220a or 270a to power my new SHOK II & T400-4. I just am not Sure if this would be a good idea or not let me know what you guys think.

I say go ahead, Sundown audio woofers can take a beating and they are very well built. I know people running 1k+ daily to SA woofers and they don't get stinky pr even warm. Maybe after an hour or more of abuse at high levels of play time they do but you will be running the E's at only 100w over the suggested rms. I'm sure just like their other woofers these are underrated as well. Just remember clean signal is key to any setup. I ran 1700w to a Z 10"v.3 from sundown and it didn't even break it in over a time period ofa month lol. As stated make sure you have clean signal and a nice box. But i would say you will be fine putting it on 500w rms

Does it include bass knob?

OP can you post pics of said clip or plug? I have never seen a plug on batt (-) terminal, seems odd to me. Also when doing big three just run a 1/0 wire along with factory wiring. And remember use fuse for run from alt to batt(+).

Would these alt's fit a 2011 malibu w/ecotec 2.4l engine?

Yea I was really digging the bc2k and thanks for the info

Looking for an amp in this range. Let me know what you have, brands i am looking for are AQ, sundown, DC, AB, RF, anything similar just drop me a line.

Well that's what i started thinking as well. So i came up with this, I will probably sell the 10 v.3 and buy a single 15" v.3 of course it's not the same cone area of 2 12's but it's more cone area than a single 12" and you don't have to seek more power haha. Unless you truly want to. Even then i'm sure that v.3 can handle close to 4k just saying. I'm sure i seen a few vids out there. As long as it's clean power i don't see why not

This is really impressing i still can't believe the amount of patience that you have Josh. Great work bro and keep it up. And i hope all goes well in your future, I read somewhere you would like to open a shop with your Dad some day. Hope that happens for you Kuz deff the talent and worksmanship is there.

Yes for the time being it was the BRZ1700 however i am currently looking for a minimum of 2.5k to throw at it. It was just laughing at me in my face with the 1700w it was getting lol. But soon very soon it will be pounding again. And i am truly impressed at how low this gets, also its a nice clear low that just sounds great. I

I also have a z v.3 and love how low it gets plus i also like the fact that my 10" requires such a small box but still pushes out an insane amount of power haha. And yes they will ask for more and more power until they have there fill. Soon i will be trying to upgrade as well to 2 12"s v.3. And yes NS's are mostly for spl purposes. V.3 are very nice and always sought after, thus why when i called Sundown last week to try and order another they said they were waiting on a shipment of motors for the v.3 kuz they were fully out of stock.(hint, this should tell you something lol)

No. You set your gain to match your head unit's output. Gain works exactly how the name implies it does, it is how much strength the input signal gains before being sent to the driver. ^ x2

Higher preout means more power signal sent to amplifier= amp gain set lower = better for less distortion. Just saying. I have a JVC KD-BT1 I bought used for $50 and when i sold my amp to a buddy of mine i left the same settings on it. His Pioneer double din only had 2v preouts so in order for it to sound as loud as when the setup was in my car we had to turn gain up some more. So yes preouts voltage matter when you are looking for less distortion and tunning by ear lol. But if you have a DD-1 or Osco, get either and just set gains using this. Amp is still going to put out same amount of power either way.

Could you get me a link? http://www.parts-express.com/pe/showdetl.cfm?Partnumber=240-125 Sorry I gave you the wrong link the first time. You need the single female to dual male. This is the correct link Maybe I'm wrong but wouldn't he need 4(y splitters) total and 1male to 2 female? I did this to my buddies vehicle and we used 4(y splitters) total usually 2 come in a pack. OP Do you currently have a sub amp hooked up? And will you be requiring all 4 channels plus a sub output? EDIT: Sorry I gave you the wrong link the first time. You need the single female to dual male. ^ this could also be done at the amp, however you still need 1male to 2female behind deck on both right and left output rca's Please clarify for me do you only have one total output rca behind deck? or do you only have one left?

So i just ordered my S MD DD-1 and wondering if you could sign it for me Steve. This SMD is going to help me set all my friends gains perfectly. Im military(Army) and i help out all my buddies here at Ft Lewis(JBLM) as far as installs and tuning, and my wife just bought me this(SMD DD-1 much needed) as a b-day present lol. My order # is: 100002493 Invoice Number: 100002493