dill30669 Posted May 20, 2011 Report Share Posted May 20, 2011 (edited) I have a 2009 Orion HCCA 15.2 in an Atrend SPL vented enclosure, the sub is hooked with 10 awg wire to an MA audio hk4000d(stable at 2 ohms...) I have the sub wired to 4 ohms right now. every time i get the bass bumpin I get a smell.. smells like burning the voice coil(blowing the sub). I cant figure why it is doing this i must have something wrong... 5/24- fixed the smell the ssf was to low, now i need to findout if i can recone it with different ohms\ 160A high output alt. 1/0 gauge big three, cap and amp 30 farad cap. another question is about a recone kit.. can i change the cone without damaging anything 15.2 to a 15.4 cone? Edited May 24, 2011 by dill30669 Quote Link to comment Share on other sites More sharing options...
Rebel4055 Posted May 20, 2011 Report Share Posted May 20, 2011 Hows your gain on the amp looking. Quote Rest In Peace mother. January 22, 1955 - February 14, 2013 http://www.stevemeadedesigns.com/board/user/35351-megrch/ Link to comment Share on other sites More sharing options...
tlee2 Posted May 20, 2011 Report Share Posted May 20, 2011 Your probably clipping Quote 6 Sundown X 15s 2 Sundown NS1 V2s C Pillar 4th order Bagged Suburban on 24s http://youtube.com/tlee333 Link to comment Share on other sites More sharing options...
stefanhinote Posted May 20, 2011 Report Share Posted May 20, 2011 Whats your voltage at full tilt? enclosure volume? enclosure tuning? ssf set to? Quote Link to comment Share on other sites More sharing options...
Supercharged DCs Posted May 20, 2011 Report Share Posted May 20, 2011 You are clipping the subwoofer. Turn your gain down, and see if the smell persists. You need to set it with an oscope to get clean unclipped power. Quote Bassless once again. Can't seem to keep a system for more than a few weeks Saving for a '06 Nissan 350z, look for build around June 2012. Link to comment Share on other sites More sharing options...
byers319 Posted May 20, 2011 Report Share Posted May 20, 2011 more then likely clipping coils like clean power Quote Link to comment Share on other sites More sharing options...
Kevin Posted May 20, 2011 Report Share Posted May 20, 2011 You need to set your gain level with an oscilloscope. Quote Link to comment Share on other sites More sharing options...
dill30669 Posted May 20, 2011 Author Report Share Posted May 20, 2011 Hows your gain on the amp looking. about half gain. sub sonic is about 25hz Quote Link to comment Share on other sites More sharing options...
dill30669 Posted May 20, 2011 Author Report Share Posted May 20, 2011 Whats your voltage at full tilt? 14.7 starting heavy hits make about 12.7 to 13.8 never had it drop below 12.7 though. enclosure volume? 3.0 cu ft enclosure tuning? believe its 35hz? ssf set to? ssf? need explanation lol Quote Link to comment Share on other sites More sharing options...
n8ball2013 Posted May 20, 2011 Report Share Posted May 20, 2011 Ssf os subsobic filter if you're tuned to 35 setting your ssf to 25 is a bit low id set it no lower than 30. Also your gains are probably too high Quote THERE IS NO BUILD LOG! 1998 Chevy Silverado ext cab Alpine CDA-9887 4 Team Fi 15s 2 Ampere Audio TFE 8.0 2 Ampere Audio 150.4 3 Digital Designs CS6.5 component sets Dual Mechman 370XP Elite alternators inbound! 8 XS Power d3400 6 XS power d680 Second Skin Stinger Tsunami Wiring Sky High A Real Voltmeter not a piece of shit stinger. Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.