Gazoo_bumpin Posted March 8, 2008 Report Posted March 8, 2008 nice i love ho that shit looks! What I'm not getting steve is where you put the router jig after you cut that tab out did it go into the tab slot to cut the middle out or what Or was the middle part just cut free hand with the router Moving where the Money Trees are
JustinT Posted July 19, 2008 Report Posted July 19, 2008 sorry to bring this back up but does it matter if you go clockwise or counter-clockwise with the router when cutting these circles? "IT SOUNDS SLOW MOTION AND STUTTERING"~~~~LOL 2 15" Fi BTLs 7.5 cf box @ 33hz Sundown SAZ-3500D Powermaster S3400 & D3100 Iraggi 300a alt SecondSkin - totally dead Knu wire
Guest Posted July 19, 2008 Report Posted July 19, 2008 go the way the bit is spinning i guess...couldnt you just make your own thread?
Airborne Posted September 10, 2008 Report Posted September 10, 2008 This site has everything! My next system is going to be bad ass! I am going to get the Jasper Jig on payday!
77-AUDIO Posted December 4, 2008 Report Posted December 4, 2008 what router bits did you use for the speaker rings... I wanna get it right the first time.. PPI dbl dinDC Level 31.77cubes net tuned to 33htz.DC audio 2.0kCT Pro Audio 8" in front, 6.5 in rear
kentb Posted December 4, 2008 Report Posted December 4, 2008 what router bits did you use for the speaker rings... I wanna get it right the first time.. spiral upcut bit New System 2 10" Fi SSD, Sundown 1500d Build I build and design enclosures(cheap price), PM ME Kicker L7 Navigator(plexiglass, fiberglass, aeroport) Build BTL 18" Escalade(plexiglass, battery tray) Build http://www.kentbaudio.com Old System
trainman0978 Posted December 4, 2008 Report Posted December 4, 2008 When you run the router , you will be able to hear and feel the router working to hard if you go against the bit rotation...Also, Meade is using the porter cable 690 ( model ) router. He is using the fixed base in those photos and if you have a router that will fit the jasper jig using the plunge base, you can set the stops and make several shallow passes so you wont be straining your bit or your router...Cutting circles with the jig goes pretty damn fast too.... once you drill your pin hole and get the router and jig on the pin, the circle is done in under a minute.... 2007 Toyota FJ Cruiser Voo Doo Blue my upgrades and "build" thread. My Kulicki Box Build -Alpine 9887 head unit, KTX-100EQ imprint-( sound quality for dummies! ). - MB Quartz 3.5" in back pillars -Sundown Audio SAX100.4 - JL Audio 3 way 6.5" component set XR653-CSi ( doors and dash ) -JL Audio 2 way Component set XR650CSi - Alpine MRD - M1005 - Alpine Type - R 12" subs -- 2 - 12" s in a Pete kulicki designed box. -Alpine High speed Ipod cable, and KCA-SC100 with Sirius sat. radio -All wiring is Stinger 12 gauge and HPM Level 3 RCAs, KnuKonceptz Kolossus Power and ground and Big done in 1/0, -270 sq. ft. of Damplifier Pro, 36 sq. ft. of Overkill Pro, 6 full sheets of Luxury Liner, and a gallon of spectrum- -2 Powermaster D680 Powercells in back FINALLY !!! I GOT IT METERED ON THE TERMLAB !!! I did a 140.2 at 42 hertz. Shoehorn, BFH, forklift,duct tape and some zip ties
dwright27 Posted December 6, 2008 Report Posted December 6, 2008 When you run the router , you will be able to hear and feel the router working to hard if you go against the bit rotation...Also, Meade is using the porter cable 690 ( model ) router. He is using the fixed base in those photos and if you have a router that will fit the jasper jig using the plunge base, you can set the stops and make several shallow passes so you wont be straining your bit or your router...Cutting circles with the jig goes pretty damn fast too.... once you drill your pin hole and get the router and jig on the pin, the circle is done in under a minute.... times 2 we are gonna need to make some smaller ones man, thinking of dropping down to 5 1/4's or 4"ers 2006 F-150 4 DC XL M2 18's Walled Daily Driver XS Power 4 DC 3.5kw Team DC Team S.P.L. Lot of Audio Technix and 1/0 DC Audio Dealer American Bass Dealer XS Power Dealer Audio Technix Dealer
zfrerichs Posted December 17, 2008 Report Posted December 17, 2008 Mine are all wavy and not perfect looking hahaha Roseville, CA
dlesman Posted July 7, 2009 Report Posted July 7, 2009 (edited) This is an awesome tutorial Steve!! Thx!! Its always nice to get a great turorial from the master! :good: Edited July 7, 2009 by dlesman
Recommended Posts