Kade Posted October 9, 2014 Report Posted October 9, 2014 I have a P3D2-10 on a P1000x5. 746w @ 1ohm to the subwoofer channel. I was wondering if I could add a P1000x1 on 2 P3D4-10 and have all 3 subs in a single box. Can it be done? What limits me from doing so? 2009 Dodge Caliber SXT (Silver) Deck: Pioneer X3600BHS Amps: RF P1000X5 Front: RF P16-S Rear: RF P1694 Subs: 1 RF P3D2-10 Cabling: Stinger 6 channel RCA, RF 4gauge kit, SkyHighCarAudio 16gauge speaker wire. Build Log: http://www.stevemeadedesigns.com/board/topic/188246-caliber-build Professional Networking: https://www.linkedin.com/in/kade-mallett-332b8a104
philrab Posted October 9, 2014 Report Posted October 9, 2014 A. I believe the D4 and D2 subs have slightly different T/S parameters. As such, I wouldn't load them into a shared chamber. B. If the three subs aren't getting EXACTLY the same amount of power, you're going to run into issues with them being in a shared chamber. 2015 Toyota Tacoma Build Thread 2007 Mazda 3; 5000K HID's, Kenwood Excelon KDC-X997, Infinity Reference 6.5 comps in front and coaxials in the rear doors, JL 320.4 four channel, Rab Designs built ported enclosure with an SA12, Kenwood monoblock, Redline Leater shift boot/e-brake boot/center console cover, JBR short shifter/shifter bushings/rear motor mount. Build Thread 1996 Mazda Miata: Kenwood Excelon HU, Alpine speaker in the doors, Clearwater (miata specific) headrest speakers. 1994 Mazda Protege: Kenwood Excelon HU, Infinity Reference 2 ways all around, 2x RF Punch 10's in ported boxes.
deeje Posted October 9, 2014 Report Posted October 9, 2014 You can't run different power to the subs if there in the same box. --2004 Toyota 4runner New Build Log -2002 Acura Tl-S Old Build Log Team DC Audio spl dust is an option you can get on the coils... it's great for extra 1000 watts of power where can i get this spl dust and how much is it. is it hard to apply? lol
Hopesndreams Posted October 9, 2014 Report Posted October 9, 2014 not a good idea imo since 2 subs are gonna see a set amount of power and then the third will see something completely different which is going to cause problems just get a new bigger amp to run all 3 L
philrab Posted October 9, 2014 Report Posted October 9, 2014 You can run different power to the subs if there in the same box. In a shared chamber? Have fun with that. My advice stands OP. I wouldn't. Opinions are like....... 2015 Toyota Tacoma Build Thread 2007 Mazda 3; 5000K HID's, Kenwood Excelon KDC-X997, Infinity Reference 6.5 comps in front and coaxials in the rear doors, JL 320.4 four channel, Rab Designs built ported enclosure with an SA12, Kenwood monoblock, Redline Leater shift boot/e-brake boot/center console cover, JBR short shifter/shifter bushings/rear motor mount. Build Thread 1996 Mazda Miata: Kenwood Excelon HU, Alpine speaker in the doors, Clearwater (miata specific) headrest speakers. 1994 Mazda Protege: Kenwood Excelon HU, Infinity Reference 2 ways all around, 2x RF Punch 10's in ported boxes.
REH Posted October 9, 2014 Report Posted October 9, 2014 You can't run different power to the subs if there in the same box. I noticed your typo, fixed for you.
Joe X Posted October 10, 2014 Report Posted October 10, 2014 Don't ask for trouble, get 3 D2 subs and a single amp to run them all at 1.3 ohm. Simple works best.
Kade Posted October 10, 2014 Author Report Posted October 10, 2014 Don't ask for trouble, get 3 D2 subs and a single amp to run them all at 1.3 ohm. Simple works best. What kind of wattage would I be looking for? 1500 @ 1ohm? 2009 Dodge Caliber SXT (Silver) Deck: Pioneer X3600BHS Amps: RF P1000X5 Front: RF P16-S Rear: RF P1694 Subs: 1 RF P3D2-10 Cabling: Stinger 6 channel RCA, RF 4gauge kit, SkyHighCarAudio 16gauge speaker wire. Build Log: http://www.stevemeadedesigns.com/board/topic/188246-caliber-build Professional Networking: https://www.linkedin.com/in/kade-mallett-332b8a104
islandpride684 Posted October 10, 2014 Report Posted October 10, 2014 Don't ask for trouble, get 3 D2 subs and a single amp to run them all at 1.3 ohm. Simple works best. What kind of wattage would I be looking for? 1500 @ 1ohm? That'll work... Build Log http://www.stevemeadedesigns.com/board/topic/186921-blk9te-07-yukon-slo-mo-build/page-3?hl=%2Bblk9te#entry2881410
Recommended Posts
Archived
This topic is now archived and is closed to further replies.