cvxsmitty58 Posted April 21, 2010 Report Posted April 21, 2010 i have a aq2200d and i was wondering where the best place to set the subsonic would be. It can be anywhere from 10 to 50 hz. Thanks
sqsux Posted April 21, 2010 Report Posted April 21, 2010 i have a aq2200d and i was wondering where the best place to set the subsonic would be. It can be anywhere from 10 to 50 hz. Thanks Its like your lowpass setting, only instead of filtering out high notes on your subs, it filters out dangerously low notes, I usually put mine around where I think 18hz would be so it would filter out notes below 18hz Start out boxy, shape as you move along. Dc Audio Team Fur
R_Mac_1 Posted April 21, 2010 Report Posted April 21, 2010 What is your box tuned at? You should set it a bit below box tuning. If your box is tuned to 35 hz, setting your SSF to 18 hz isn't going to do you much good. 2002 Pontiac Bonneville SSEi Pioneer DEH-P6000UB Alpine SPX-17REF 6.5" components (active) Sundown SAX-50.4 Sundown z15 (3 cubes @ 35 hz) Sundown SAX-1200D 2006 Buick Rainier CXL AWD V8 Stock Bose system 12" Alpine Type E in aeroported box Profile AP1000M
splzx3 Posted April 21, 2010 Report Posted April 21, 2010 y the fuck do u need 10 hz? and x2 wut r_mac_1 said ________________________________________________________________________ deepsilencer, on 22 Aug 2011 - 17:32, said: splzx3, on 22 Aug 2011 - 17:27, said: i had my fun on one of his videos...till he blocked me then i got my mother into it lol after her he closed the comments xD lol your mom is a G! WTF, I never thought I'd have a conversation about cross dressers and trans-genders on a car audio forum.
bassl0va Posted April 21, 2010 Report Posted April 21, 2010 Set it for like 8hz below your tuning. That should be fine, can always move it up a bit if it's too low. My RE MT 18" wall build Former build, farewell beloved wall.In progress, Toyota Starlet build This forum has a massive boner for ridiculous electrical upgrades.
kirill007 Posted April 21, 2010 Report Posted April 21, 2010 Or you can use a test tone that's 10hz(or below port tuning,and set the subsonic at max first, and lower it till you think it reaches max excursion without damaging the driver. Thinking is the root of all problems... You ALWAYS get what you pay for.
Neo_frog Posted April 21, 2010 Report Posted April 21, 2010 So far I haven't seen a very good response. r_mac_1 was the closest. Find your box tuning and play a tone (on repeat) that's 5hZ under at 1/2 to 3/4 volume. Turn the subsonic up slowly until the note starts to cut out then you know your roll off starts there. Need an install? Hit me up.[email protected]Got car audio questions? Check here first!Everything you need to know. =]http://www.stevemeadedesigns.com/board/topic/83029-everything-you-need-to-know/
Decaf Posted April 21, 2010 Report Posted April 21, 2010 o come on guys, just guess... as long as its below/at tuning its fine not to mention that 1/2 the people arent even tuned to what they think they are mine is all the way down... because i know every note i play
sqsux Posted April 21, 2010 Report Posted April 21, 2010 So far I haven't seen a very good response. r_mac_1 was the closest. Find your box tuning and play a tone (on repeat) that's 5hZ under at 1/2 to 3/4 volume. Turn the subsonic up slowly until the note starts to cut out then you know your roll off starts there. But alot of people dont have the time money or resources available to figure their actual frequency, and if you're going around playing 10 to 25hz sine waves for normal driving time, then you're kinda slow, if you pay attention to what you're playing there's no problem with guess or turning it all the way down, that's not the right way to do it I understand that but you can't always be perfect. Edit: and my box isn't 35hz, that's old, I'm just usualy on my phone so I havnt updated anything, if you were even talking to me lol. Start out boxy, shape as you move along. Dc Audio Team Fur
Recommended Posts
Archived
This topic is now archived and is closed to further replies.