jizazz12

so your saying that i should use three 6" areos for the pair of 15's ?this is going to be a daily not realy going for numbers.

looking for some advice,working on a new box for two lvl 4 15's.previous box was 7.5 cubes tunned to 33 Hz. using four 4" psp areo's.subs were being powered by two jl1000/1's in the trunk of a sonata. just got a new car a 2007 Chevy impala building a box right around the same size,thinking of using 6" areos instead of the 4". wondering if two 6" areo's will be enough or should i just stick with the 4"?also will be using same amps for now but will be upgrading soon any help on this will be greatly appreciated .

my lvl4's are in 7.5 cubes and do quite well in this space, box is tuned to 33 hz.. but as said above allot depends on vehicle and power.

dom at iraggi, or rob over at dc power . both are great companies and can point you in the rite direction.

have you tried going to the precision port website, you can find out all the information you need there.

x two on the liquid nails,but resin is always a good way to go as well.

if your building your encloser for a daily beater than stick with the first set of measurements, if your going more for competing in a spl class than use the spl measurements provided by rusty.

to much power on the sub.

as said above all are good choices,it all depends on installation and personal preference.

can't see anything,getting an error message

Angel Gonzalez aka jizazz12 Hollywood, Florida proud to be a member of S.M.D. .

thank you for responding so quickly,as soon as i get my new truck i'll be in touch.

on the norm do you offer a cut list and how much would a box design for two dc audio LVL4 XL's run ? i will be getting a truck in the next couple of weeks and just wanted to inquire.not sure which yet but truck is going to be a Tahoe or a Bourbon.

it's not going to take 1000 per coil but it is a great sounding sub. i did an inatall with two 15's for a buddy and they get down fo sho.

looking good and sounding better every time i see it.got a question for you,are the p2's wired the same as the 10's that you put in the escalades doors?just wondering because i have the same 8's was wanting to try something similar.

thanks for the heads up on this,i was seriously thinking about going the a.q. rout.

thanks for all your input.and Loganberry if i make the decision to go with the stetsom I'll get with you on watcha you want for em. thanks again all.

hey everyone,planning a new build and am looking at some different amps. i know some of the folks on here have or have had some experience with stetsom and was just wondering how there performance is really. looking to power four D.C.LVL 4 15's was looking at the Stesom V6K2D 1 ohm or 2 OHM . also was thinking about a couple of sundown 3500's or a 4500,looked at the RF 2500 1 but it's kind of pricey for my budget.

are these cones going to be available as a standard or are they special order?

you should be good i have three amp's and a audio control matrix running of mine. i just ran the remote off my radio to a small disrto block an out from there.

P.C. tools spyware doctor with antivirus detection, been running it for three years and so far its never let me down.

whats up fellas, my son lives in palm bay I'm going up the end of the month maby i slide thrue and check you all.

i use my car for work and i spend the majority of my time in it . i have been into car audio since i was young so i just decided to take my hobby to work with me makes me feel at home.

currently i have two lvl 4 15's with a J.L. audio 1000/1 on each what would the real time power gain be if i were to swap out amplifiers ?

20'' is fine usually most recommend 12" to 18" from starter batt it shouldn't be a problem.