sundownz

If the dust cap is loose it will sound funny. You can use a CA glue or a Goop type glue if you like -- otherwise we can fix it for you if you bought it new that way.

NS v.2 with the new NS v.3 yellow spider pack in place. As is typical with our drivers they are designed to handle around the rated power in free air so the ratings are a "worst case" conservative rating. As you can see this pack has no issues with the 2500D and the measured FS is still 37 Hz with only about 4-5 minutes of play time on it.

When they ship the FedEx system will send out tracking automatically, yes.

NeoPro-8 models are now SOLD OUT. Also -- all NeoPro speakers will face a small price increase due to the Neo cost increases. The next run of NeoPro-8s will include 4 ohm models as well. We will have more in stock in June... the demand for these really snuck up on us exponentially rather than just a gradual increase so supply was literally pulled right out from under us! We should have more steady data on the demand in the future on these. New / Old Pricing : NeoPro-6.5 : $99 / NA NeoPro-8 : $105 / $99 NeoPro-10 : $129 / $115 The 10" has a much bigger piece of Neo in it so was more affected. If Neo goes back down in the future we'll adjust accordingly -- we may also offer an alternative Ferrite line for those that don't care about weight.

Yes. If you have 15s you need a certain model 12-spoke with the bigger landing -- but the 10/12 spider and 18 spider work on any frame.

NS v.3 spider packs are in... the spiders are like the Z v.3 units but with an extra layer -- and the 15/18 models have triple leads. These will be standard issue on NS v.3 and optional on other models. They are yellow to immediatly identify them as the NS stiffness pack (5 layers) as opposed to Z v.3 (4 layers). I may even bring in a 6 or 7 layer pack for dedicated SPL purposes. Currently we use NS v.1 / v.2 spiders for SPL purposes stacked to the appropriate level.

Indeed -- it's a stamped frame to reduce cost for the E line. As far as stamped frames go it's very strong and very functional clearance-wise but not tough enough for our bigger motors.

Yah all orders placed before the weekend are good to go. We had a very large order from a distributor on Saturday that is really putting us out of parts.

Okay couldn't resist so I dropped two 2500s in and maxed it out : That was all she had -- any more and it would leave the gap. So I guess I didn't get my 150 but I'm not too sad over it

Been here all weekend with customers and whatnot anyway... so decided to drop one in the Jeep real quick. The Jeep hasn't had much love lately and I was using it to haul scrap metal for a while (hence the wooden truck bed) but I decided to break it back out. One 4500D @ 1 ohm with one extra SPV-70 for battery. My box has a pretty high rise so probably seeing 3-4 ohms or so actual on the amp so not a ridiculous amount of juice yet. Sub still has a good bit of usable throw remaining. So I guess the next phase is to actually put in a more usable battery setup for multiple amps and use two amps at 0.5 ohm to get the sub to full stroke. Not sure yet if that will get done today as I've been at the shop way too much recently, haha. I think 150+ is do-able with it.

They are going out of here pretty quickly -- we'll probably have a temporary back-order on them due to the unforseen massive demand. I'll have to count stock on Monday... 18s and 12s may already be back-ordered due to baskets.

*thumbs up* It has taken years of hard work to get here but we are really trying to step everything up another big notch!

http://www.sundownau...l?category_id=2 Z v.3

Do you have original coils in with vents ? Is it a pole plugged motor ?

Original thread is closed as ordering has been shut down. They will be leaving our factory March 8th - 13th and arrival time is 25 - 35 days... so we will be from 1st to 2nd week of April which is a bit behind schedule but not too bad. We sold such a huge quantity it will probably take 2 weeks or more to get them all tested and shipped out. If any stock remains regular ordering will open back up after that point. We have to make sure that we have enough fully QC passing units to supply all currently paid pre-orders before taking any more orders. If you missed out... we have two more production runs scheduling for arrival in ~May and another for arrival in ~June-July but the pricing will be regular and not pre-order special.

!!! PRE ORDERING IS CLOSED !!! Too many have been sold and we have to cut it off to make sure we have enough for everyone who already paid. If there are any remaining regular ordering will re-open a week or two after arrival. ETA is around the first week of April or so -- slightly behind schedule.

Cool - let us know how they work out. We don't make many 10s in these but we do offer them.

Production is wrapping up -- here is a completed production unit : ETA is looking like end of March to first of April -- a hair off original ETA but not too bad assuming customs goes smoothly.

Production is wrapping up :

Glad you like it

Box volume and tuning sounds good. Can you do sub and port backward ? Friend of mine has a center console box in a truck and that sounds really good in his.

Assuming you aren't trying to play midrange on them they would do well.

It's over 150 dB on the dash now with the 3 spider woofer (which is quieter) due to some changes in the setup. Need to build another 2 spider woofer as we damaged the first one (4000+ watt burps on an eight can do that). More details later on

I've also changed plans to 9x 15" woofers on a flat back wall -- 4th order band-pass. Figured this will be more efficient than parallel or even a clam-shell setup.