john253a

first idd work out your max dimensions then sub up,back or fwd, port up,back of fwd do you want slot or aero port? port standing up, or lying down? How do you want to tune them, (and if low do you have good surround to components a low tune)

here's one 1 draw up for a mate with some modifications to suit you measurements

this may help it may need some tweaking but its all there

2x5" will work well if you can use or get

post some pics and people may be able to show you where you may have gone wrong or give you some pointer on better ways to do

somethings not right when you sealed off port for a test, it still should be loud (not as loud but still loud) and should have a flater response curve. idd say check all your wiring and build a different box, something ain't right there

13.5"(h)x 24"(w)x 29.5"(d) 4.38cuft gross slot port 12(h)x4(w)x35.5(L) 0.15cuft sub displacment 31.5hz @3cuft net

if you can go from 13 to 14" high

just some stuff i found when i look into them

http://www.stevemead...dynamics-horns/

first things first port is too small, a single 6" is only 7:1 ratio you want between 9&13:1 for aero, 12&16:1 slot so youll need 2x6" @ 33" long (14.1:1) or or 4x4" @33"long external for a 4cuft net box (12.6:1) witch ever size you chose youll need that much in front of port, there are a few options put some of port inside box to shorted it up on outside or build the entire port inside the box something like this would be ideal if you can fit

redarc do them, there one of the best, http://redarc.com.au/home Arb and oppositlock sell them them as there used in there dual battery setup you can also get projecta, but you will be in replacing it under warranty all the time as there poorly made http://www.bcf.com.au/online-store/products/Projecta-Dual-Battery-Kit.aspx?pid=283674#Description

fit a blower from a 4agze should give you about 4psi then with the left over coin get your self a good set of pipes. the stock computer should handle the psi increase, if not youll need to fit a rising fuel reg

this is my old system, just sold it and got myself a hsv R8 its all kicker started out as a simple build Head unit Eclipse AVN6000 Front surround (coaxial mounted +6db to tweeter) Kicker QS65.2 @ 75rms ea Rear surround (coaxial mounted +6db to tweeter) Kicker QS65.2 @ 75rms ea front/rear surround amp Kicker ZX700.5 Sub amp Kicker ZX400.1 Kicker Zx700.5 (same as surround) Subs 2x Kicker cvt8.4 @ 210rms ea Kicker cvt12.2 @ 400rms all the doors are dynamated inside and around speaker +floor and rear wall car '09' sr5 Toyota hilux d4d custom leather,twin sunroofs, alloy bar, hardtop, tub liner, etc head unit eclipse anv6000 rear surrounds with dynamat rear subs before amps mounted and backseat refitted up front is kicker 0/1 wire from battery to amps 0/1 ground goes to distribution block then 0/1 to engine block, also from block is 3x 4gauge cables to factory bolts on body/rails and ecu A few options i look at for amps and crossovers only problem was 4 crossovers and only 3 fitted so i had to fit them in the doors, amps stayed where they were done some add-on about 3 months after finished install added another amp and changed components to actice The crossovers had this as an option So a added another Kicker ZX650.4 But unfortunately I'd have any picks of amps on back bored for first install and any of addishnal amp install All I did was stack the 650.4 ontop of 700.5 as there were the same size amp

Not a bad starting or finishing point $990 with 6x9 rears or 1040 with component rears edit: you build box and install

front surrond Alpine-R $180 http://www.sonicelectronix.com/item_34364_Alpine-SPR-60C.html rear surround either another alpine-r 6.5 component or Alpine type-r 6x9 $129 http://www.sonicelectronix.com/item_8552_Alpine-SPR-69C.html front/ rear suround amp MB Quart 100x4@4 $140 http://www.sonicelectronix.com/item_33005_MB-Quart-FX4.100.html Sub amp MB Quart 1500rms@1 $190 http://www.sonicelectronix.com/item_23875_MB-Quart-ONX1.1500D.html Sub Fi Q 15 ported with some options $350 https://ssl.perfora.net/www.ficaraudio.com/sess/utn;jsessionid=154f72b7eaea5ec/shopdata/0050_Speakers/0030_Q/product_overview.shopscript

1000 for sub/amps and speakers isnt that bad of a starting price does that include h/u as well

A DD 9918Z with everything you can through at it

i done a dual cab truck 4 doors and floor, no roof for $250 in dynamat floor,firewall, behind rear seat and rear shelf with http://www.sonicelectronix.com/item_3132_Dynamat-Xtreme-Door-Kit-10435.html and for every 2 door http://www.sonicelectronix.com/item_3132_Dynamat-Xtreme-Door-Kit-10435.html this stuff takes a long time to apply to doors and i would invest in the app tool its not the best stuff on the market, but it was the right price and the easiest to apply