lifted stepside Posted July 22, 2011 Author Report Share Posted July 22, 2011 Not sure on the amp I just know (what he told me) its 1500rms. the box they're in is a mtx terminator prefabulous box and they're 12s Quote Link to comment Share on other sites More sharing options...
will77530 Posted July 22, 2011 Report Share Posted July 22, 2011 you could get a dc lvl 3 12 its 1.5 ^3 Quote Link to comment Share on other sites More sharing options...
1lownoma Posted July 22, 2011 Report Share Posted July 22, 2011 Might get a suprise man I saw 4 DD 8's do some major work at Slamfest a few years back Quote Link to comment Share on other sites More sharing options...
Supercharged DCs Posted July 22, 2011 Report Share Posted July 22, 2011 Not sure on the amp I just know (what he told me) its 1500rms. the box they're in is a mtx terminator prefabulous box and they're 12s 2 SA-8s on a quality 1.2k amplifier in a good box should surprise the hell out of them Just sayin lol. Quote Bassless once again. Can't seem to keep a system for more than a few weeks Saving for a '06 Nissan 350z, look for build around June 2012. Link to comment Share on other sites More sharing options...
lifted stepside Posted July 22, 2011 Author Report Share Posted July 22, 2011 Ok been playin around with the RE box builder turns out after displacement and everything I'm right around 1.5 cubes . is that enough for the 2 sa-8s? thats with the box tuned to 34hz like sundown recommends. opinions? Quote Link to comment Share on other sites More sharing options...
Supercharged DCs Posted July 22, 2011 Report Share Posted July 22, 2011 That should be enough. I actually think 1.2cubes would be better, as you plan to give them quite a bit over rated... How much port area? Quote Bassless once again. Can't seem to keep a system for more than a few weeks Saving for a '06 Nissan 350z, look for build around June 2012. Link to comment Share on other sites More sharing options...
lifted stepside Posted July 22, 2011 Author Report Share Posted July 22, 2011 I was worried that would be enough I can do 1.2cubes easy. The port is 3.07in wide and 10.5in tall so 32in of port Area is that right? Is there supposed to be a gap between the top plate and the port? This is my first ported box so I'd really like to do it right the first time. And Is it ok if the port downfires? Quote Link to comment Share on other sites More sharing options...
Socky Posted July 22, 2011 Report Share Posted July 22, 2011 If i remember right RE's box calculator isnt correct. What amp are you going to be using? An audioque 1200d is a good suggestion since it has a little clip light. Quote Jeep Cherokee 4dr -4.75 in front, new rusty's 4.5 in rear leafs -micky thompson 35x14.50x15 -locker rear -Rusty's offroad Engine/transmission/transfer case/crossmember/gas tank skid plates -Warn front bumper with 8000lb winch -Custom rear bumper -Warrior product tube doors (summertime) -Optima redtop (starter) -26XK miles and still runs like a bat out of hell Kenwood H/U 1/0 wire, 136 amp alt 200 ah batteries 12.7 daily 2 Apsm 1500 @ 2 ohm strapped on zv3 d1 with ns softparts Mb quart 125.4 wired to 4 aura 6's 3.6 cube box tuned to 36 plays down to 23hz Link to comment Share on other sites More sharing options...
lifted stepside Posted July 22, 2011 Author Report Share Posted July 22, 2011 Actually, The aq1200 is what I had in mind just havent set anything in stone. Quote Link to comment Share on other sites More sharing options...
DRauck Posted July 22, 2011 Report Share Posted July 22, 2011 Downfiring the port? As in... into the floor? Quote 2011 Honda CR-Z Mugen 12" Kicker SoloX Subwoofer Rockford Fosgate t20001bd Pioneer AVIC-X930BT Head Unit Build Log Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.