audiofanaticz Posted November 29, 2011 Author Report Posted November 29, 2011 nah.. debating on going outside tho and do a lil work since I bought a few bottles of glue.
Socky Posted November 29, 2011 Report Posted November 29, 2011 Sounds like a good idea, did the swelling go down in your finger? Jeep Cherokee 4dr -4.75 in front, new rusty's 4.5 in rear leafs -micky thompson 35x14.50x15 -locker rear -Rusty's offroad Engine/transmission/transfer case/crossmember/gas tank skid plates -Warn front bumper with 8000lb winch -Custom rear bumper -Warrior product tube doors (summertime) -Optima redtop (starter) -26XK miles and still runs like a bat out of hell Kenwood H/U 1/0 wire, 136 amp alt 200 ah batteries 12.7 daily 2 Apsm 1500 @ 2 ohm strapped on zv3 d1 with ns softparts Mb quart 125.4 wired to 4 aura 6's 3.6 cube box tuned to 36 plays down to 23hz
audiofanaticz Posted November 29, 2011 Author Report Posted November 29, 2011 yea, its almost back to normalish, still a lil swelling but I can bend it almost all the way again. Kinda why I havent done much except a few 45s, and it really inflamed my finger. Im in no hurry, nothings going anywhere, but Id like to get baffles cut.
lilboom Posted November 29, 2011 Report Posted November 29, 2011 whhhoooooahmaan...lookin like a beast SuperBass check out⊂ http://www.youtube.com/Bassknots 129.3 meca 136.8 db drag (60 hz peak) http://bassknotsstereo.blogspot.com/ comment/subscribe and stay tuned ,working on 150 db http://www.stevemead...r/page__st__380
TheBetterMethod Posted November 29, 2011 Report Posted November 29, 2011 Yes YES Get baffles cut! 2005 Subaru Outback Wagon Pioneer 9400BH Fi Q 15, SAZ1500dV3 The first build>>> http://www.stevemead...-outback-build/ 140.9 @ 36hz Sealed on dash! REBUILT!!! 2 Fi Q 15s, 2 SAZ1500dv3 146.9 @ 39hz dBDRA certified
audiofanaticz Posted November 29, 2011 Author Report Posted November 29, 2011 went outside for a little bit, gotta be up early so I didnt have much time in the garage got like 2 things done, and baffles where not neither. HA!! This piece was a lot of work... but still to long. To put it simple, I had to make 6 matching angles on each end, then have it the needed length. got the other board on the port rounded over a tad made the window ledge mold into the 45 then stuck the leds inside to get an idea.
RickyFriery97 Posted November 29, 2011 Report Posted November 29, 2011 Box is looking damn good dude! Your are good with angle cuts, that shits hard! Can wait to see how this sub handles the power 2014 Chevy Silverado Crewcab 1994 Chevy Full Size blazer
BassJunkie Posted November 29, 2011 Report Posted November 29, 2011 Badass, you make these look easy. Looks great 1986 C20 Suburban 9 American Bass XFL 15's B2 M1MKII 14v XS Power Batteries Maxwell Caps Acoustical energy is free. Electrical energy is not you havent lived until you've hit a screw with a router.
audiofanaticz Posted November 29, 2011 Author Report Posted November 29, 2011 Box is looking damn good dude! Your are good with angle cuts, that shits hard! Can wait to see how this sub handles the power it can be a pain from time to time, but its a lot cheaper then dumping gallons of resin inside your box to build up the corners A compound miter saw would make them a lot quicker, maybe thats my next purchuse Badass, you make these look easy. Looks great thanks buddy!
bre2ts Posted November 29, 2011 Report Posted November 29, 2011 box looks great brian! you weren't kidding with the amt of displacement in it. but will make for good air flow. Feedback 1 | Feedback 2 you win some, you lose some
Recommended Posts
Archived
This topic is now archived and is closed to further replies.