Ryan929 Posted October 11, 2012 Report Share Posted October 11, 2012 *Not a Vs. thread* Which would be more power efficient being as there is only a couple dollar difference in price? 1/0 OFC: http://audiotechnix....-ofc-power-wire OR 2/0 welding cable: http://www.temcoindu...le/WC0026.html# I was planning on upgrading and just wondering which would be better, and obviously the welding cable is bigger but the 1/0 is oxygen free so i wasnt sure. Thanks guys. Link to comment Share on other sites More sharing options...
iwalkwithedead Posted October 11, 2012 Report Share Posted October 11, 2012 IMO: 1|0 OFC Vehicle Build | Searching for a MK4 Jetta or Chevy Xtreme S-10Computer Build Log - Blue Moon | NZXT Phantom 410 | Unfinished/Sold Computer Build Log - Blue Tsunami | Bitfenix Prodigy Cobalt Blue | Liquid Cooled! Link to comment Share on other sites More sharing options...
soundstream15 Posted October 11, 2012 Report Share Posted October 11, 2012 I have 2/0 welding cable for my big 3 and it works just fine, idk if there is a difference but welding cable will handle heat better so that's why I used it for the big 3 Link to comment Share on other sites More sharing options...
BassJunkie Posted October 11, 2012 Report Share Posted October 11, 2012 2/0 /thread 1986 C20 Suburban 9 American Bass XFL 15's B2 M1MKII 14v XS Power Batteries Maxwell Caps Acoustical energy is free. Electrical energy is not you havent lived until you've hit a screw with a router. Link to comment Share on other sites More sharing options...
Guest Posted October 11, 2012 Report Share Posted October 11, 2012 well how much current are you going to be passing through said cable? Link to comment Share on other sites More sharing options...
Ryan929 Posted October 11, 2012 Author Report Share Posted October 11, 2012 well how much current are you going to be passing through said cable? My system is 14.4 volts and it would be run to my amp which is about 2000rms Link to comment Share on other sites More sharing options...
Tito DeLatorre Posted October 17, 2012 Report Share Posted October 17, 2012 2/0 Link to comment Share on other sites More sharing options...
Socky Posted October 17, 2012 Report Share Posted October 17, 2012 if it was me, it would be 2/0, my bro just got some that 1/0 and its tiny looking compared to the welding cable 1/9, but it has more stands. Jeep Cherokee 4dr -4.75 in front, new rusty's 4.5 in rear leafs -micky thompson 35x14.50x15 -locker rear -Rusty's offroad Engine/transmission/transfer case/crossmember/gas tank skid plates -Warn front bumper with 8000lb winch -Custom rear bumper -Warrior product tube doors (summertime) -Optima redtop (starter) -26XK miles and still runs like a bat out of hell Kenwood H/U 1/0 wire, 136 amp alt 200 ah batteries 12.7 daily 2 Apsm 1500 @ 2 ohm strapped on zv3 d1 with ns softparts Mb quart 125.4 wired to 4 aura 6's 3.6 cube box tuned to 36 plays down to 23hz Link to comment Share on other sites More sharing options...
Guest Posted October 17, 2012 Report Share Posted October 17, 2012 voltage doesn't matter when choosing power wire. you need to know the CURRENT DRAW in AMPS. no, not an amplifier. an amp. its the unit of measurement for current. unless you're running over like 300amps, then stick with 1/0. Link to comment Share on other sites More sharing options...
Kyblack76 Posted October 17, 2012 Report Share Posted October 17, 2012 voltage doesn't matter when choosing power wire. you need to know the CURRENT DRAW in AMPS. no, not an amplifier. an amp. its the unit of measurement for current. unless you're running over like 300amps, then stick with 1/0. This amperage be key....... SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.