Jump to content
DC Sound Lab

DC 10k amp hum at low gain


Recommended Posts

I had a dd-1 but the shops setting with N is cope , i just don't think only 1/4 gain is where the 10k starts to clip,

awesomeness-1.jpg

(4)DD 9918's

(2)DC 10k

8 6.5" focals

2 DD SS4 mid amps

Audison Bit One processor

Jl-cl-rlc line driver

iPad in dash

Dual Irragi 320a alts

8 batcaps 4000's

Second Skin sound deadened

Link to comment
Share on other sites

I had a dd-1 but the shops setting with N is cope , i just don't think only 1/4 gain is where the 10k starts to clip,

Yeah but that don't matter. It will clip at a different point depending on your setup. HU, RCA's and line voltage.

My Nendo 3500's clipped at 65% gain in my old build now they clip at half.

Edited by Amart88
Link to comment
Share on other sites

iPad as h/u and Jl cl-rlc line driver , maybe could run through the bit one

awesomeness-1.jpg

(4)DD 9918's

(2)DC 10k

8 6.5" focals

2 DD SS4 mid amps

Audison Bit One processor

Jl-cl-rlc line driver

iPad in dash

Dual Irragi 320a alts

8 batcaps 4000's

Second Skin sound deadened

Link to comment
Share on other sites

And all RCA are the same no difference in signal from a coat hanger to mos expensive rca

awesomeness-1.jpg

(4)DD 9918's

(2)DC 10k

8 6.5" focals

2 DD SS4 mid amps

Audison Bit One processor

Jl-cl-rlc line driver

iPad in dash

Dual Irragi 320a alts

8 batcaps 4000's

Second Skin sound deadened

Link to comment
Share on other sites

All I am saying is the gain in not a set level. It is to match your RCA output voltage. If you have low voltage the gain would need to be a bit higher to compensate. etc.

Link to comment
Share on other sites

I have very high o/p voltage

awesomeness-1.jpg

(4)DD 9918's

(2)DC 10k

8 6.5" focals

2 DD SS4 mid amps

Audison Bit One processor

Jl-cl-rlc line driver

iPad in dash

Dual Irragi 320a alts

8 batcaps 4000's

Second Skin sound deadened

Link to comment
Share on other sites

I have very high o/p voltage

There you go. Just answered your own question.

The gain does not have to be high for the amp to do it's rated power. You are likely fine at 1/4 as that's where it matches up.

Link to comment
Share on other sites

My 9k hums when the DD-1 shows distortion.So if your amp is humming then that mean your hitting the point of distortion. The amps gain is only there to match the amps output to the source unit. So if you have bass boost turned up or your line driver turned up then your amp wont need to be turned up much to match the input signal.

Vehicle
2007 Chevrolet Avalanche(Co-Co)

DNX9980HD
6 Team Fi 15's(King Edition)
3 DC 9k's
8 Nendo PWX 8's
4 Custom Steg 4" Super Tweeters
1 DC Audio 175.4
1 DC Audio 90.4
Rockford 360.3
3 DC Power 370xp Alts(Externally regulated)
21 D1600's
2 D4800's
All SMD RCA's
AudioTechnix Deadner
Viper Alarm

My YouTube- http://www.youtube.c...NG?feature=mhee
Link to buildlog- http://www.stevemead...4-15s-2-dc-9ks/
Link to UBL- http://www.stevemeadedesigns.com/board/topic/165059-ublkings-avalanchecoco-new-build-starting8-king-edition-15-team-fis-in-a-wallyes-a-wall/

96576a0.jpg

Banner3_zpsa237d00a.jpg

Link to comment
Share on other sites

Please no shitstorm.....

Does the amp actually hum? or the subs it is hooked to?

Yupp the amp actually hums. Very slight though

edit: My 2200 did hum aswell

Edited by DubinDodge

 

'01 Dodge Stratass Sealed Trunk Build Log
2008 Honda Fit Sport Build Log

On 10/3/2013 at 10:00 AM, ROLEXrifleman said:

Anyone who says they knew everything they wanted out of life at 19 can go suck a bag of dicks cause they are lying to themselves or brought up in a cult.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Who's Online   2 Members, 0 Anonymous, 1556 Guests (See full list)

×
×
  • Create New...