Deadly hertzz Posted December 26, 2013 Author Report Share Posted December 26, 2013 I get no signal or nothing even if I put the probe directly n the amp how could I troubleshoot the dd1 8 sundown sa 12s walledSaz3000 at .5HO altAll ofc Sky high wireAlpine componentsRockford power mids Link to comment Share on other sites More sharing options...
n8ball2013 Posted December 26, 2013 Report Share Posted December 26, 2013 I camt watch the video You bypassed the linedriver right? Your rca still has a signal at the amp right. Make sure you have a good ground. Try using a different speaker output try the pos then the negaticw until you gwt signal. Sometimes you dont get signal until a certain volume. THERE IS NO BUILD LOG! 1998 Chevy Silverado ext cab Alpine CDA-9887 4 Team Fi 15s 2 Ampere Audio TFE 8.0 2 Ampere Audio 150.4 3 Digital Designs CS6.5 component sets Dual Mechman 370XP Elite alternators inbound! 8 XS Power d3400 6 XS power d680 Second Skin Stinger Tsunami Wiring Sky High A Real Voltmeter not a piece of shit stinger. Link to comment Share on other sites More sharing options...
Deadly hertzz Posted December 26, 2013 Author Report Share Posted December 26, 2013 Ok thanks I just went an gave it a try finally got the 40hz to detect But still no luck on the 1khz tone 8 sundown sa 12s walledSaz3000 at .5HO altAll ofc Sky high wireAlpine componentsRockford power mids Link to comment Share on other sites More sharing options...
Kyblack76 Posted December 26, 2013 Report Share Posted December 26, 2013 Watch your xover settings. You can turn the line voltage down. (was me, id just remove the line driver) that said, again, watch the x over set up and points. SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
Deadly hertzz Posted December 26, 2013 Author Report Share Posted December 26, 2013 This is all with the line driver out of the equation I can get it to detect the 40 but never the 1khz could it be since it's from the sub output on the head unit it wouldn't send a tone that high through that RCA or something 8 sundown sa 12s walledSaz3000 at .5HO altAll ofc Sky high wireAlpine componentsRockford power mids Link to comment Share on other sites More sharing options...
Kyblack76 Posted December 26, 2013 Report Share Posted December 26, 2013 The 1k sig comes from the sub amp?Then turn your xover UP SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
Deadly hertzz Posted December 26, 2013 Author Report Share Posted December 26, 2013 I have everything set on the amp just like the manual says everything flat on head unit hpf off loud off there's a sub control feature that goes from 60-300hz and I put that all the way up also 8 sundown sa 12s walledSaz3000 at .5HO altAll ofc Sky high wireAlpine componentsRockford power mids Link to comment Share on other sites More sharing options...
Deadly hertzz Posted December 26, 2013 Author Report Share Posted December 26, 2013 I also tried plugging my RCAs from my Highs amp into this amp just to make sure the sub control Had nothing to do with it and still no 1khz to detect 8 sundown sa 12s walledSaz3000 at .5HO altAll ofc Sky high wireAlpine componentsRockford power mids Link to comment Share on other sites More sharing options...
OrionStang Posted December 26, 2013 Report Share Posted December 26, 2013 Are the crossovers full open on your headunit and amps? SMD Super Seller My Feedback Thread Link to comment Share on other sites More sharing options...
MrSkippyJ Posted December 26, 2013 Report Share Posted December 26, 2013 I think the amp is capped at 300. Won't likely ever see a 1khz tone out of it. F150: Stock 2019 Harley Road Glide: Amp: TM400Xad - 4 channel 400 watt Processor: DSR1 Fairing (Front) 6.5s -MMats PA601cx Lid (Rear) 6x9s - TMS69 Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.