MatthewBigBossWilliams Posted November 10, 2014 Author Report Share Posted November 10, 2014 Also going to have to worry about gain matching the two amps, cause if they put out even slightly different power levels you're going to run into issues quickly. The CC and DD were mailed to me and are enroute. I am just getting an early start on set up so all I have to do is gain match and play Link to comment Share on other sites More sharing options...
CNF Kevosinn Posted November 10, 2014 Report Share Posted November 10, 2014 one amp per coil @ 1ohm gain matched with the CC1 after you DD1 one of the amps *** SuperSeller Status Verified *** ( http://www.stevemeadedesigns.com/board/topic/25829-super-sellers-buyers/ ) "kevosinn's" astro van 8 custom Sundown Zv4 18's 4 Sundown scv 6000's CNF Distribution CNC parts Skyhigh wire some batteries SMD Meters and tools used on the installhttp://www.stevemeadedesigns.com/board/topic/172877-kevosinns-vanwest-coast-skyhigh-car-audio-vehicle/ 16,000 watt walled silverado build.http://www.stevemeadedesigns.com/board/topic/161965-walled-silverado-4-hdc4-15s-4-crescendo-3500s-and-much-more/ 8,000 watt 1999 Subaru legacy outback. Build log here: http://www.stevemead...ru/page__st__60TEAM CNF Distribution Link to comment Share on other sites More sharing options...
philrab Posted November 10, 2014 Report Share Posted November 10, 2014 Also going to have to worry about gain matching the two amps, cause if they put out even slightly different power levels you're going to run into issues quickly. The CC and DD were mailed to me and are enroute. I am just getting an early start on set up so all I have to do is gain match and play Just checking. Skipping that step even if everything is wired right is going to cause you serious heartburn. 2015 Toyota Tacoma Build Thread 2007 Mazda 3; 5000K HID's, Kenwood Excelon KDC-X997, Infinity Reference 6.5 comps in front and coaxials in the rear doors, JL 320.4 four channel, Rab Designs built ported enclosure with an SA12, Kenwood monoblock, Redline Leater shift boot/e-brake boot/center console cover, JBR short shifter/shifter bushings/rear motor mount. Build Thread 1996 Mazda Miata: Kenwood Excelon HU, Alpine speaker in the doors, Clearwater (miata specific) headrest speakers. 1994 Mazda Protege: Kenwood Excelon HU, Infinity Reference 2 ways all around, 2x RF Punch 10's in ported boxes. Link to comment Share on other sites More sharing options...
MatthewBigBossWilliams Posted November 10, 2014 Author Report Share Posted November 10, 2014 All in all I have an idea on how to do it. I just know this is risky so I wanted to make sure. Link to comment Share on other sites More sharing options...
MatthewBigBossWilliams Posted November 10, 2014 Author Report Share Posted November 10, 2014 Also going to have to worry about gain matching the two amps, cause if they put out even slightly different power levels you're going to run into issues quickly. The CC and DD were mailed to me and are enroute. I am just getting an early start on set up so all I have to do is gain match and play Just checking. Skipping that step even if everything is wired right is going to cause you serious heartburn. What if I just set the volume up halfway on both amps. Still a bad idea? Link to comment Share on other sites More sharing options...
Jhunt94 Posted November 10, 2014 Report Share Posted November 10, 2014 Also going to have to worry about gain matching the two amps, cause if they put out even slightly different power levels you're going to run into issues quickly. The CC and DD were mailed to me and are enroute. I am just getting an early start on set up so all I have to do is gain match and play Just checking. Skipping that step even if everything is wired right is going to cause you serious heartburn. What if I just set the volume up halfway on both amps. Still a bad idea? Volume? I hope you're not referring to the gain as a "volume" because those are definitely not the same. 2007 Ford F-150 Reg. Cab. Flareside250 Mechman AlternatorSky High Car Audio Big 3 XS Power D3400Rockford Fosgate 1/0 amp kitRockford Fosgate T1500-1bdcpRockford Fosgate T400-4DC Audio Lvl 4 12"Rockford Fosgate Punch 6.5" componentRockford Fosgate Punch 6x8Pioneer AVH-P2300DVDSMD Volt Meter Link to comment Share on other sites More sharing options...
MatthewBigBossWilliams Posted November 10, 2014 Author Report Share Posted November 10, 2014 Also going to have to worry about gain matching the two amps, cause if they put out even slightly different power levels you're going to run into issues quickly. The CC and DD were mailed to me and are enroute. I am just getting an early start on set up so all I have to do is gain match and play Just checking. Skipping that step even if everything is wired right is going to cause you serious heartburn. What if I just set the volume up halfway on both amps. Still a bad idea? Volume? I hope you're not referring to the gain as a "volume" because those are definitely not the same. I meant the gain on the amp. I was thinking about puting that half way up on both amps and trying it out that way. Link to comment Share on other sites More sharing options...
Jhunt94 Posted November 10, 2014 Report Share Posted November 10, 2014 Also going to have to worry about gain matching the two amps, cause if they put out even slightly different power levels you're going to run into issues quickly. The CC and DD were mailed to me and are enroute. I am just getting an early start on set up so all I have to do is gain match and play Just checking. Skipping that step even if everything is wired right is going to cause you serious heartburn. What if I just set the volume up halfway on both amps. Still a bad idea? Volume? I hope you're not referring to the gain as a "volume" because those are definitely not the same. I meant the gain on the amp. I was thinking about puting that half way up on both amps and trying it out that way. That is a very bad idea 1. because most of the time the gains do not need to be set that high 2. If you do that you'll possibly clip the hell out of the sub 3. I'd be surprised if you could even get both of them in the exact same position Just wait for the DD-1 and CC-1 to get to you. It's better to be safe than sorry, especially when you dealing with expensive equipment. 2007 Ford F-150 Reg. Cab. Flareside250 Mechman AlternatorSky High Car Audio Big 3 XS Power D3400Rockford Fosgate 1/0 amp kitRockford Fosgate T1500-1bdcpRockford Fosgate T400-4DC Audio Lvl 4 12"Rockford Fosgate Punch 6.5" componentRockford Fosgate Punch 6x8Pioneer AVH-P2300DVDSMD Volt Meter Link to comment Share on other sites More sharing options...
reedal Posted November 10, 2014 Report Share Posted November 10, 2014 never mind. ^^ beat me to it SMD Tool Map https://www.stevemeadedesigns.com/board/topic/193176-smd-tool-map-new-november-2014/ Build log https://www.stevemeadedesigns.com/board/topic/197217-reeds-03-tahoe-hat-sqaq-singer-xs-shca-cockbox-80prs/?page=32 Link to comment Share on other sites More sharing options...
hispls Posted November 10, 2014 Report Share Posted November 10, 2014 I meant the gain on the amp. I was thinking about puting that half way up on both amps and trying it out that way. This is not going to end well..... Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.