Sign in to follow this  
Followers 0
darkie14

Bad turn OFF pop with 3Sixty.3

12 posts in this topic

12 minutes ago, n8ball2013 said:

Keyed power source and If necessary a relay. 

Where the hell you been boss!?!?! 

Share this post


Link to post
Share on other sites

I'm around. Just busy as fuck and a ton going on

1 person likes this

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By Wicks
      Hey everybody,
      Time for me to join the party!
      The Harmon Kardon factory system in my M3 just wasn't doin' it for me so I decided to rip err all out and do some WERK!
      So here's what I started with:


      I didn't like any of the factory components, so I'm building it head to toe, here's a list of the main components:
      Mechman 320A (to replaced the factory 120A)
      One run each (power/ground) of 0 gauge OFC, front to back (stock battery is in the trunk)
      Two XS Power XP3000's (jumped in on the group buy recently)
      Alpine INA-W900 (As you will see later, this was quite a battle to install)
      Alpine Imprint H100
      Alpine Sirius Tuner
      Coax signal cables
      12Ga Knu Kord speaker wire for Mids/Highs
      8Ga Stinger OFC for subs/highs amp
      Hertz HSK130 5 1/4" Components
      Rockford Fosgate Punch200DSM for the highs (OLD SCHOOL from 1993!)
      DC Audio 2.0K
      DC Audio XL12m2
    • By Mike Howard
      have a 1999 ford explorer sport with the 4.0 ohv motor. i have a 270a 15v h/o alt installed in oem location. wanting to add my 2nd 270a alt. it can go in place of the ac pump or elsewhere..  anyone got a lead to one? 
    • By valow
      Hey all -
      Brand new 3sixty.3 installed, and I'm curious how many of you dive deeply in to the 31 band EQ? I'm no expert, and I don't yet have a DD-1 so I'm not exactly aching to jump in to it. In order to tune it correctly, I'm assuming I need to just bite the bullet and go buy a DD-1, right?
      Do you leave it default from the OEM setup, then jut adjust amp gains? Or are you better off going in and trying to build the correct curves for each type of music. Essentially I'd use 3 presets - Hip Hop, Rock, and probably a more mellow set for talk radio, etc.
      '14 Ford F-150 Super Crew (Sony Premium Sound)
      Set up is:
      Kenwood 9106D
      RF P400x4
      RF 3sixty.3
      Drivers
      2 Kenwood eXelon 10"
      Front doors - Polk DB 6.5" w/ tweets in pillars
      Rear doors - Polk MM 6.5" w/ tweets in doors
      Passive crossovers in all doors
      Stock head unit
      Using the high level input on the 3sixty, it's configured to use full range for all doors with HP, and subs in rear with LP.
    • By ibanezrg134
      I am swapping my alt out for a mechman with a 1.75 inch pulley. I measured my stock pulley to be 2.5 inches. The belt for my car is approx. 84.5 inches. What size belt would i need.
      In order to swap my alternator out i need to remove the front passenger tire so using the "try multiple belt sizes until it fits" isn't the best approach for me
      Any help would be appreciated.
    • By skaraudio
      We had a customer that came to us wanting to upgrade the stock stereo system in his 2002 Ford Excursion to Skar Audio! He wanted it to be loud but also wanted it to sound clean, so we went to work!
      What we installed:
      3 Pairs of Skar Audio RPX68's
      2 Skar Audio VD-12's in a custom built enclosure
      1 Skar Audio LP-80.4ABv2 4-Channel Amplifier
      1 Skar Audio LP-1000.1D Monoblock Amplifier
      1 Pioneer AVH-X4700BS Head Unit
      1 Back Up Camera
      1 Audiovox 13.3" Flip Down Monitor
      Onto the photos!

      Here are some before photos!




      RPX68's!


      LP-80.4ABv2 and LP-1000.1Dv2 installed underneath the 2nd row seats!


      Onto the enclosure!






      Finished Product!





      Built by Head Builder Greg Gazos with assistance from Director of Operations Shane Neville.
  • Who's Online   22 Members, 0 Anonymous, 707 Guests (See full list)