crispy_chick3n
-
Posts
1485 -
Joined
-
Last visited
-
Days Won
3
Content Type
Profiles
Forums
Events
Media Demo
Store
Collections
Videos
Everything posted by crispy_chick3n
-
i have had mine for about 3-4 months now. used it quite a bit for electrical repairs in customer vehicles, i have only gone through about a quarter of the can of butane. constantly running you could proably get 1-2 hours out of a full torch
-
home depot has a butane soldering torch, comes with 5 different heads, a roll of solder and a case for around 15 bucks, and then a can of butane is like 3-4 bucks. i spent less than $20 on my set, and i couldnt be happier with it. it works great, gets hot fast. linkey linkey
-
Planking
crispy_chick3n replied to Fennygolf's topic in Off Topic - Random, Misc posts - the forum "Junk Drawer"
-
using stumbleupon today as usual. came across this website and realy thought about what i want to do before i die. before i die i want to connect with all my teachers from my past schools – college, high school, junior high, all of it. let them know how they have shaped my life. so my question is this what do you want to do before you die? just think, "what if i were to die tomorrow what would be the one thing i would want to do?"
-
How are you goin to insult the person tryin to help you. i have plenty of common sense thank you.
-
well there's your problem
-
cant figure out how to upload photos from my phone.
-
i have run that mtx i mentioned earlier on nothing but the big 3 and a yellow-top up front in a mustang before. it puts out 2200 rms at 2 ohms. you could get by with it. although for that amp it did help when i put a kenetic hc1800 in the back, but you could do it with stock electrical. its just a little bit expensive tho. lol
-
http://www.sonicelectronix.com/item_8652_MTX-Thunder-Elite-4001D-TE4001D.html ^^^this one might be a little bit of overkill tho http://www.sonicelectronix.com/item_23549_Hifonics-Brutus-BRZ2100.1D.html http://www.sonicelectronix.com/item_11551_Kicker-ZX2500.1-08ZX2500.1.html i have used all 3 amps that i have linked to. overall i like the mtx the best. it actualy puts out, and it looks good for show as well
-
your air/fuel mix would be as rich as the computer will allow it to be. the air/fuel mix being extremely rich wont affect performance, it will just kill gas mileage. if you want to turn the CEL off follow this here tutorial. it might take a trip th the local radio shack for the supplies, but it does work. after you install the bypass go down to advance auto parts, and have them clear the codes on your car. im not sure if that will solve the gas mileage problem or not tho. best of luck to ya.
-
http://www.sonicelectronix.com/item_33006_MB-Quart-FX1.400.html http://www.sonicelectronix.com/item_11877_MTX-Audio-Terminator-TN250-1.html http://www.sonicelectronix.com/item_17257_Orion-Cobalt-CO500.1-CO5001.html ^^never tested that brand before tho
-
sounds to me like when you were playing the lows that maybe a spider came loose and is to blame. have you given your subs a good through visual inspection yet? that is always one of the first troubleshooting steps. i would almost put money on a spider breaking loose.
-
Wrote a note said be back in a minuteBought a boat and I sailed off in itDon't think anybody gonna miss me anywayMind on a permanent vacationThe ocean is my only medicationWishing my condition ain't ever gonna go away
-
got the truck raised about an inch and a half in the front. it actualy sits level now.
-
should be signal. heater is just a constant voltage. signal is the changing voltage that you want.
-
honestly if budget is a main concern. you dont have to rebuild the engine. you could just replace the rod bearings themselves. hell when i had my s-10 like a week before i was going to sell it i spun a rod bearing. i didnt want to put a whole lot of money into it, so i dropped the oil pan off, and replaced the rod bearings with the engine still in the truck. it was kind of a bitch to do, but it only cost me around 90 bucks. now if this truck was driven for a while with a spun bearing, more than likely there will be some damage to the crankshaft, could be scored, could be out-of-round, could be both. if it were me doing this, i would buy a re-man and slap it in, then rebuild the old motor up nicely, swap em, and sell the factory motor.
-
Never gonna grow upNever gonna slow downWe were shinin' like lighters in the darkIn the middle of a rock showWe were doin' it rightWe were comin' aliveYeah, caught in a Southern summer, barefoot, blue jean night
-
Server upgrade last night - 8 gigs
crispy_chick3n replied to meade916's topic in SMD NEWS / ANNOUNCEMENTS
