Jump to content

Bump4life

S.O.T.M. Winner
  • Posts

    4665
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by Bump4life

  1. so currently i am running the speaker wire from subs out the port to the amp. i feel it looks bad, which it does. so i want an alternate way to do this. so i saw a lot of you use bolts through the box and connect the wire to the bolts? which type of bolts do you use? i dont want to introuduce much resistance if any into the run. i love the direct leads for a reason. or should I just cut a whole in the back of box stick wire through and seal it off with silicone? what other ways do you guys get wire from subs to amp cleanly and such any input on this would be appreciated!
  2. haha good song. and looks like its doing work. any deadner on that trunk? aha. goes to show you what xs power bats can do for you.
  3. considering you have all stock electrical i would say 15.2 volts seems unusual. in addition depending on what type of amp you have it may not like that high of a voltage.
  4. if you have enough money to buy a battery, put that towards wiring and get the battery as soon as you can later. believe it or not, every part of a system is important. even the wiring haah. a chain is as strong as its weakest link. so if you get shitty wire your stuff is goin got not be as good/ possibly break. if you are struggling for cash Knukonceptz 0 gauge CCA wire will hold you over until you get some cash for 0 gauge OFC. don't skimp on wire cause then you might end up having to pay more for other stuff that breaks or you wont be happy with the output of your system
  5. Univeristy of Michigan as well. Mechanical Engineering Repping U of M slamminbeatzz and I
  6. what kind of plywood? like birch? birch is good
  7. ahh i see. sorry i was a little slow. i just didnt know which bat was stock and which bat was XS sinch both said bat in your diagram. Thanks for clarification!!
  8. what? english please? the car is 1995. and has a steel frame. not a unibody. but im doing 2 runs (one pos and one neg) min, i just want to know if i should do more than just that. what 1995 car has a "steel frame" 99% of all cars n suvs are unibody a mercedes does... and doesnt unibody mean no frame like joints are glued and what not togehter. i have a frame that runs the whole length of the car. i have this
  9. yep that makes sense. one more thing. should i connect alt to stock bat or XS power bat? does it matter? and should all amps be on xs power battery?
  10. im going to do the negative run straight form the alt casing. and where is the extra 1/0 frame ground going to and from?
  11. ok sounds good. thanks. dont i already have a solid battery ground in rear? and also when i have XS power bat in rear too i was told to put pos run from alt to stock bat and neg run from alt to XS bat is this true?
  12. what? english please? the car is 1995. and has a steel frame. not a unibody. but im doing 2 runs (one pos and one neg) min, i just want to know if i should do more than just that.
  13. hey whats up. summer is coming. spring is here. lets get this system going. so currently running M1C @ .5 ohm (no problems at all, doesnt get hot), DD C2C (160x2 @ 2 ohms), and JL 400/4 (100x4 @2ohms) using max spec on all amps. so total current draw max is (150A+40A+40A=230A) i have stock alternator and big 2. engine block to frame, and batter neg to frame. stock battery location is in trunk. so i dont have run from alt to bat pos. my question is, should i do 2 runs total (one + and one -) from alt to rear bat? or will i need more for power running? i am using KNU OFC 0 gauge. keep in mind there will be large stock battery and an XS D5100 in rear. currently my voltage drop is from 13.9 down to 12.4 on full tilt. my plan is to also add another battery(d5100 located right noext to stock attery to right in small space. currently i have the beefiest stock battery known to man. idk what it is but it holds its own. mercedes does well. and also stock wiring throughout car is 4 gauge.
  14. grounds are very important! they can save you a lot. but what load are you running that amp at? im assuming 2 oms?
  15. they should like that. make sure you get them each 4 cubes net and youll be golden
  16. agreed^^ but if you tune super low you can go even lower. idk what you are looking to do exactly
  17. 2 HDC3's would love 3.5k. personally when i had HDC3 12s it hit lows aweosme! at least in my opinion. I had an AQ2200 on one HDC3 12 for a while. so if you send them unclipped power they can take 2krms. as far as hitting the lows who told you they wernt the best for hittin glows? i mean there are better speakers IMO but AQ HDC3 are still awesome. if you tune around 32hz which i wouldnt go much below and feed them 3.5-4k to 2 HDC3 15s im sure you will be happy.
  18. ok i edited it now lets get some better reesults haha
  19. maybe i shoulda been more specific to my vechicle. yea this question kinda sucks. FAIL
  20. Isn't this great? BIue skies, fresh-cut grass, birds chirping.

    1. Show previous comments  2 more
    2. IBleedMusick

      IBleedMusick

      I saw a chipmunk in the bushes humping a turnip...lol National Security if you're a movie buff.

    3. Bump4life

      Bump4life

      hahaah yes I am. if you didn't know mine came from Happy Gilmore. no homo slammin ahah

    4. IBleedMusick

      IBleedMusick

      Yeah I caught that figured I would blend it with another line that went with it well.

  21. just curious, why do you think cable size is fine? when my buddy upgraded from 4 gauge to 0 gauge with same exact amp that OP has it raised his voltage drop by almost 3 volts
  22. the cable running to my batteries is 4 gauge and I havent done a big 3 yet until I swap out my engine for the zetec so I can upgrade the alternator from the stock. 4 gauge all the way, 4 gauge from the 2nd battery to the distribution block, and 4 gauge to the t1500 amp, but 8 gauge for my component amp since I cant fit anything bigger in it id put a lot of money on it that that is your problem. im surprised that your mono amp doesnt tank first. yea man that t1500 puts out more than rated or at least tries to. upgrade all that wire to batteries to 0 gauge, and do big 3 0 gauge and i bet that solves your problem. the 8 gauge to the highs amp is ok. alright I'll do that, I'll see how much 0 gauge is for this whole setup will be, then do a big 3 after I get my replacement engine. is there an adapter to connect 0 gauge to my t1500 amp? because its max power cable size is 4 gauge yes there is. the one i used was 0 gauge to 4 gauge reducer from knuconceptz. also let us know your voltage on full tilt like Kranny suggested, that will tell a lot
×
×
  • Create New...