Fosgatefeind Posted July 11, 2012 Author Report Share Posted July 11, 2012 I actually like this thread,.. And was really hoping to see a resolution. Really, stay at it, take advice and good luck bro. Give it hell. I am. I try to learn as much as possible and do my best. There will be a resolution for sure Buildlog: http://www.stevemeadedesigns.com/board/topic/146515-2007-monte-carlo-ls-build-new-plans-with-dc-audio/ TEAM DC AUDIO www.Dcsoundlab.com Link to comment Share on other sites More sharing options...
sactownstang Posted July 11, 2012 Report Share Posted July 11, 2012 1400 Watts total on 2 DD 9500 series? That's a joke for power with those subs. Put at least 3500+ to them and numbers will shoot up. Link to comment Share on other sites More sharing options...
Kyblack76 Posted July 11, 2012 Report Share Posted July 11, 2012 I thought the M3 would toss out over 2 large all day, and at 12volts...... Then of course more at higher...... guess im wrong,...?.... par for the course... SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
OrionStang Posted July 11, 2012 Report Share Posted July 11, 2012 I never even noticed that, I thought he had 3500's. You need a pair of M4a's OP, one for each sub. SMD Super Seller My Feedback Thread Link to comment Share on other sites More sharing options...
stroupe79 Posted July 11, 2012 Report Share Posted July 11, 2012 install looks good..as mentioned I would rebuild without the center port divider..make sure to have all inside corners rounded...roundover everything outside the box...and get more power to those subs...your running 1400w to subs that are rated 1600w rms and upto 6000w peak http://www.ddaudio.com/products/mobile-audio/woofers/9500-series.aspx http://www.stevemead...cherokee-build/ 2005 Jeep Grand Cherokee Alpine CDE-hd148bt Alpine PKG-RSE2 PRV Audio (4) 6MB200 front/rear doors PRV Audio (4) TW350Ti dash/rear doors Kicker KX350.4 Obsidian Audio (1) 18 D4 v2 revamp (2) Stereo Integrity HT 18d2DC Audio 1.2k5.25ft^3 tuned @34hz revamp Infinite Baffle Cpillar AudioTechnix 60mil deadenerKnuKonceptz & SkyHigh wire (complete setup) Link to comment Share on other sites More sharing options...
mrd6 Posted July 11, 2012 Report Share Posted July 11, 2012 Rink is 100% sealed off as I have found no leaks. And how would I take the middle piece out? It's glued nailed and screwed in? Like people are saying, you probably just dont have the power to get the subs moving enough. But another thing to do would be to double check if it is actually all sealed off. It may look like it is but when things get to flexing and whatnot during a burp that can change, gaps can open up and you can get weird cancellation. Try burping with the trunk open, if you are louder open than closed, you are not sealed off enough and doing so could raise your score quite a bit My Build Log: http://www.stevemead...-sundown-power/ Team NorthWestSPL Link to comment Share on other sites More sharing options...
Fosgatefeind Posted July 11, 2012 Author Report Share Posted July 11, 2012 I had it closed on the first burp of my second run and keen on the second burp of my second run. No change Buildlog: http://www.stevemeadedesigns.com/board/topic/146515-2007-monte-carlo-ls-build-new-plans-with-dc-audio/ TEAM DC AUDIO www.Dcsoundlab.com Link to comment Share on other sites More sharing options...
Fosgatefeind Posted July 11, 2012 Author Report Share Posted July 11, 2012 I need to get another m3a but I need another without the m3a engraved on the top to match mine now Buildlog: http://www.stevemeadedesigns.com/board/topic/146515-2007-monte-carlo-ls-build-new-plans-with-dc-audio/ TEAM DC AUDIO www.Dcsoundlab.com Link to comment Share on other sites More sharing options...
alaskanzx5 Posted July 12, 2012 Report Share Posted July 12, 2012 build an amprack to where on amp sits under the other. then the engraved part wont matter because you will only be able to see the top of one of them. just make sure you give them both the room they need to breath t1500bdcp 2 t2d4 15" 1 t600.4 1 t400.2 1 set p1 tweets singer alt, tons of wiring, smd vm-1, 80prs, back seat delete, still in the works, aiming for a 145-147 with the ability to play 25hz up to 50hz. Link to comment Share on other sites More sharing options...
cjvue Posted July 12, 2012 Report Share Posted July 12, 2012 Honestly i really do feel that although the m3a is not enough to push those subs to their full potential, it should at least do a better number. My Build Log- T E A M S U N D O W N A U D I O - 2013 DbDrag WF SS1-2 - 5th Place 154.6db 2013 MECA Mod3 CA State Final Champ 153.4db Powered by: Sundown Audio Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.