harlemn8ive Posted May 10, 2014 Report Posted May 10, 2014 My setup will have my mids at 1.3 ohms. what amps are everyone else using for less than 2 ohm impedance? 300+ per channel Check out my build slow but... slow and steady wins the race http://www.stevemeadedesigns.com/board/topic/185561-1st-build-budget-toyota-mark-2/
Broke_Audio_Addict Posted May 10, 2014 Report Posted May 10, 2014 You looking for 2 channel or 4 channel amps? That being said a lot of people's definition of "music" is a clipped 30 hz sine wave with some 80 IQ knuckle head grunting about committing crimes and his genitals.
bighossf150 Posted May 10, 2014 Report Posted May 10, 2014 Rockford Used to have a loud truck 2009 Corvette Z06, H/C/I, 150 shot, g force tune, 730rwhp/690rwtq 2013 F-150 limited, MPT Tune, leveled on 35"s
harlemn8ive Posted May 10, 2014 Author Report Posted May 10, 2014 Either more importantly 2 channel Check out my build slow but... slow and steady wins the race http://www.stevemeadedesigns.com/board/topic/185561-1st-build-budget-toyota-mark-2/
White Lightning Posted May 11, 2014 Report Posted May 11, 2014 Why would you want to run that low of a ohm load ?? Kenwood / HELIX / Linear Power (For The Love Of Music) / Brutal Sounds / OverKill Electric Co Questions About Sound Quality ?? Try Here ... Sound Quality, What does it REALLY mean ?? SMD SOTM Winner "White Lightning" 1997 GMT400 Chevy Silverado "The Green Dickle" 1994 GMT400 Chevy "Phantom Dually" Randal's 2007 Chevy Avalanche (we haven't named this one yet) Dylan's "Brutal" 17 Chevy Cruze RS Hatch
harlemn8ive Posted May 11, 2014 Author Report Posted May 11, 2014 Because i have 3 sets of mids... Check out my build slow but... slow and steady wins the race http://www.stevemeadedesigns.com/board/topic/185561-1st-build-budget-toyota-mark-2/
Ryan929 Posted May 13, 2014 Report Posted May 13, 2014 Why are mids generally wired at 2 ohms or above as compared to subs that can be wired below 1ohm? Why is it ba. To wire mids low?
Bump4life Posted May 13, 2014 Report Posted May 13, 2014 lose damping factor. aka control of cones. aka bad sound quality. with subs and bass its not as noticible to the average user. Buyer/Seller Feedback Thread: http://www.stevemead...5015-bump4life/ MB C220 153 Trunk Car Build Log: http://www.stevemead...d/#entry1840136 MB C280 Ipad Dash SQ Build Log: http://www.stevemeadedesigns.com/board/topic/194484-bump4lifes-new-benz-tony-c-relay-kit-pictures-ce-electric-audison-front-stage-installed/ My SPL Log: http://www.stevemead...__fromsearch__1 BMW M340 xDrive Stock, for now. Corner Load 10" maybe soon. But does 10s in the 1/4... Best Scores out of a trunk 153.0 sealed legal full tilt clamped 5524 @ 42 hz 154+ windows down, 155+ kick
jdshott Posted May 13, 2014 Report Posted May 13, 2014 Orion old school amps can get down and dirty 0.5 ohm load. There are a few new school amps that can do the same . More impotantly have you checked the actual ohm load with a good dmm . Not all speakers are dead on with the resistance . No 1 But me paid for this stuff and NO FREEBIES so no brand names (No Free Advertisement ) A SQ head unit 6 5.25 2 X 6x9s 7804 P400.4 4001D 1 34s (Maybe time to change brand) 4 X 15" s !/0 @ 2/0 OFC Wiring :morepower1: :morepower1: ill say it like i always say it. F##K the DD-1. I don't care if you or anyone buys one. (well i do, but that isn't my point) Get an O-scope in the very minimum and learn how to use it or you are just guessing your settings like every other noob. once you master the O-scope then step up to a DD-1 or even better a DD-1 Plus.
mrd6 Posted May 13, 2014 Report Posted May 13, 2014 For what its worth, my crossfire bmf600.2s are running at 1.5 per channel measured dc resistance and its no big deal for the amps. They stay cool and sound nice... Is this 1.3 measured dc resistive or calculated nominal impedance you want to wire to? My Build Log: http://www.stevemead...-sundown-power/ Team NorthWestSPL
Recommended Posts
Archived
This topic is now archived and is closed to further replies.