Loops12 Posted August 26, 2015 Report Posted August 26, 2015 Looks good. How do you like the deadener? Quote
reedal Posted August 26, 2015 Author Report Posted August 26, 2015 Looks good. How do you like the deadener? It's good in my opinion, but having never used any deadener until today, or any butyl based products at all for that matter, I can't compare it to anything. It was easy to lay on the panel and the outer skin of the door, but the inner skin was difficult due to the components of the power windows. There were no issues with the butyl sticking though (with and without the heat gun, as it stuck to anything it touched. I didn't use my heat gun on the door, just the panels. I think it's a good product 1 Quote SMD Tool Map https://www.stevemeadedesigns.com/board/topic/193176-smd-tool-map-new-november-2014/ Build log https://www.stevemeadedesigns.com/board/topic/197217-reeds-03-tahoe-hat-sqaq-singer-xs-shca-cockbox-80prs/?page=32
Keagan-Z06 Posted September 4, 2015 Report Posted September 4, 2015 Finally found your ride, looking good man! What do you estimate in total for sound deadning door panels and floors. Not cost but how many sheets and feets? Quote HU: Pioneer 4100 NEXSubs: 2 Rockford Fosgate R2SD4-10"Amp: Rockford Fosgate P500-1bd wired @ 1ohmFront: Polk Audio Components DB6501Amp: Pioneer GM A5602 wired @ 4 ohmRear: Polk Audio Coaxials db651s(2) OM-1s, (1) VM-1
Jeff4661 Posted September 4, 2015 Report Posted September 4, 2015 Like the carbon fiber alot... How hard was it to apply? Quote Current build 05 Yukon SLT http://www.stevemeadedesigns.com/board/topic/195350-jeffs-05-yukong-wall-build/
reedal Posted September 4, 2015 Author Report Posted September 4, 2015 Finally found your ride, looking good man! What do you estimate in total for sound deadning door panels and floors. Not cost but how many sheets and feets? I will have to answer that question when I finish it. I just haven't had time. Quote SMD Tool Map https://www.stevemeadedesigns.com/board/topic/193176-smd-tool-map-new-november-2014/ Build log https://www.stevemeadedesigns.com/board/topic/197217-reeds-03-tahoe-hat-sqaq-singer-xs-shca-cockbox-80prs/?page=32
reedal Posted September 4, 2015 Author Report Posted September 4, 2015 Like the carbon fiber alot... How hard was it to apply? You'll need a heat gun or hair-dryer, and I'd recommend a staple gun to hold it in place, because I did not do that at first and the heat from summer had it peel back a little bit Quote SMD Tool Map https://www.stevemeadedesigns.com/board/topic/193176-smd-tool-map-new-november-2014/ Build log https://www.stevemeadedesigns.com/board/topic/197217-reeds-03-tahoe-hat-sqaq-singer-xs-shca-cockbox-80prs/?page=32
reedal Posted September 14, 2015 Author Report Posted September 14, 2015 Another little clip. There isn't anywhere to park and play around me (at least not respectfully) so no full tilt walk around yet. Next time I go to my hometown which is in the middle of nowhere I might whip something up. The best I can do is 45mph+ driving videos for now. I like my little setup, still needs work. I'm lacking on the free time and workspace though. I'll try to update as I go though. Still need to finish laying down the rest of my deadener. I need to finish applying it to the drivers side door, and the rest is going on the roof, and then any left over will go on the rear hatch, then I'll buy more as I need it to cover as much as I can through the entire vehicle. Thanks for looking Quote SMD Tool Map https://www.stevemeadedesigns.com/board/topic/193176-smd-tool-map-new-november-2014/ Build log https://www.stevemeadedesigns.com/board/topic/197217-reeds-03-tahoe-hat-sqaq-singer-xs-shca-cockbox-80prs/?page=32
RedWolf Posted September 14, 2015 Report Posted September 14, 2015 So I happened upon this clean blue beauty and for a price of almost half of all the others of similar year and mileage, I snatched it up. My build plans with it are to move my current system from the explorer into this since i will no longer own the explorer in a short time. The equipment being: HU- Pioneer DEH-80PRS Subs- Two SoundQubed HDS312D2's Amps- SoundQubed Q1-3500.1; AudioQue 90.4 Mids & Highs- CDT CL61A Wires- All Sky High 1/0, RCA's, 12ga speaker wire Power- Haven't decided on an alt yet, gotta contact singer, see what he's got. I don't think I'll go with anything over 300A on the alt. I'll have a D3400 under the hood, and I've got a D4700 i had bought for a cruze that I'll keep by the amps. Hopefully I can get started on transferring it all this weekend. I've got duty saturday so i'll have all day sunday to knock it out. The only things that need bought are the D3400 and the alt. I'll post pictures as i go through the install. edit: fixed the pictures Very clean looks great! Quote
reedal Posted September 14, 2015 Author Report Posted September 14, 2015 Very clean looks great! Thanks man, there's still a lot left for me to do unfortunately. Quote SMD Tool Map https://www.stevemeadedesigns.com/board/topic/193176-smd-tool-map-new-november-2014/ Build log https://www.stevemeadedesigns.com/board/topic/197217-reeds-03-tahoe-hat-sqaq-singer-xs-shca-cockbox-80prs/?page=32
reedal Posted October 23, 2015 Author Report Posted October 23, 2015 Haven't done much lately for anyone looking at this. I threw some deadener on the roof (no pics ) it was a bit of a bitch to get the headliner back up. I had a buddy but he's more of a spectator than a helper. but I hope the deadener will help the crazy roof rattle. I can't stand it, so we'll see. My ship is going underway for five weeks, so I won't be on much if at all after next week Quote SMD Tool Map https://www.stevemeadedesigns.com/board/topic/193176-smd-tool-map-new-november-2014/ Build log https://www.stevemeadedesigns.com/board/topic/197217-reeds-03-tahoe-hat-sqaq-singer-xs-shca-cockbox-80prs/?page=32
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.