My Lexus ISF Sound System Diagram

[meade916]

Its the best i could do with Microsoft Paint...but here is the "official" system diagram for my Lexus ISF. I don't think i missed anything. I also dropped my x-over frequencies to give a better idea of what i did.

FYI: The PBR 300x4 is running my rear door speakers by itself and has a switch to turn them OFF for better imaging. I can turn them on any time but i prefer to roll with JUST the front stage on.

of course, if you want to see how i got all of this in my car, click this link and prepare for about a thousand pictures.

http://www.stevemeadedesigns.com/board/topic/142076-ubllexus-is-f-sound-system-install-mechman-270a-alternator-installed-page-5/

[Maebros]

looks good simple and to the point. but jesus i diudnt realize you had that much in there

Edited October 23, 2012 by Maebros

[roscoe1129]

k looks good. I see your p3's are at 80hz & down... cool to run not bandpassed?? just wondering cuzz I am going to run my p3 8's probably bandpassed from 40-80...

[Real96SS]

I guess Im not computer savy enough because I have no clue how to even start something like thjs in paint. Thats a really good layout though and I really like how you plugged your frequencies in there also. A+

[08tahoe]

Pretty cool

You have a lot of stuff in there lol.

[alaskanzx5]

i would have listed it to where it goes head unit on top, then 3sixty, front sound stage, the rear sund stage and then the sub stage. would have been a little bit easier to see but looks good none the less. right before i saw this thread i though about doing this same thing after looking at the rockford sema show line up.

[meade916]

k looks good. I see your p3's are at 80hz & down... cool to run not bandpassed?? just wondering cuzz I am going to run my p3 8's probably bandpassed from 40-80...

nope, same frequency as the woofer. I was going to BP them but my Sensai (not Sensai from here) says no. I was also gonna do a center channel. He said no. What Terry Soohoo says, i do. Bottom line. The rear speakers were smearing the image, so those were put on a switch, which i haven't switched back on since we did our EQ'ing and time alignment. Its LOVELY.....and isn't even done yet. I have a session with RF on November 7th (they are flying out) with a 5 mic array. Then i will go back to Terry again to see if he thinks it needs anything else.... and it should be REAL lovely by then.

[roscoe1129]

k looks good. I see your p3's are at 80hz & down... cool to run not bandpassed?? just wondering cuzz I am going to run my p3 8's probably bandpassed from 40-80...

nope, same frequency as the woofer. I was going to BP them but my Sensai (not Sensai from here) says no. I was also gonna do a center channel. He said no. What Terry Soohoo says, i do. Bottom line. The rear speakers were smearing the image, so those were put on a switch, which i haven't switched back on since we did our EQ'ing and time alignment. Its LOVELY.....and isn't even done yet. I have a session with RF on November 7th (they are flying out) with a 5 mic array. Then i will go back to Terry again to see if he thinks it needs anything else.... and it should be REAL lovely by then.

sweet thanks!

[meade916]

i would have listed it to where it goes head unit on top, then 3sixty, front sound stage, the rear sund stage and then the sub stage. would have been a little bit easier to see but looks good none the less. right before i saw this thread i though about doing this same thing after looking at the rockford sema show line up.

i prefer to start from the beginning with power, source, processors, amps then drivers....

[bassface]

Do you use the i-pad for all the tuning and the i-phone for the music storage?