Sheena Posted January 4, 2013 Report Share Posted January 4, 2013 i bet luke was all cool until cj said your shit is voided now. the mistake is bearing down on him. 09 Civic EX KDC-X395 (2) SKAR Audio VVX-12 Skar Audio SK-1500.1 4 cu ft @32 (new box and more port soon) Firing Forward not sealed off Stock 80 Amp Alt Big 3 In 1/0 Knu 2 Runs To The Back 1 Pos 1 Neg In 1/0 Knu DD-1'd 13.8v drop Link to comment Share on other sites More sharing options...
CleanSierra Posted January 4, 2013 Report Share Posted January 4, 2013 I am looking into my crystal ball...I foresee this thread getting locked. Im not the one you want to try to troll. Just a fyi for you. Link to comment Share on other sites More sharing options...
bighossf150 Posted January 4, 2013 Report Share Posted January 4, 2013 Your either ballsy as hell or dumb as hell to drill into an amp that Im guessing costs around $2k Used to have a loud truck 2009 Corvette Z06, H/C/I, 150 shot, g force tune, 730rwhp/690rwtq 2013 F-150 limited, MPT Tune, leveled on 35"s Link to comment Share on other sites More sharing options...
sprkn_ranger Posted January 4, 2013 Report Share Posted January 4, 2013 Check out my build log! 4 Havocs in a blowthrough http://www.stevemeadedesigns.com/board/topic/187506-sprkn-rangers-blowthrough-build/ Link to comment Share on other sites More sharing options...
Nate Futuristic Posted January 4, 2013 Report Share Posted January 4, 2013 LOLOLOLOLOL i used up all my likes right away yeah i would have made a whole different bracket rather than drill ONE hole i think it has been stated enough though lmfao down rpping vanderbilt. 30 miles from victoria. i own the 3rd loudest setup here out of 3. but i did put together all 3 setups ^^ Cant wait to swalllow Ghost's babies Link to comment Share on other sites More sharing options...
Cox Posted January 4, 2013 Report Share Posted January 4, 2013 such an easy little tack job......whyyyyyyyyyyyy!!!!! Kenwood Excelon x396AQ2200Fi Q 12XS D3400 XS XP30001/0 RADAFLEXStinger volt meter Mechman 240a alt Link to comment Share on other sites More sharing options...
OrangeJuiced Posted January 4, 2013 Report Share Posted January 4, 2013 Taking it to a welding shop probably would be worse than the hole. There is a lot of heat applied and you have a chance at ruining the board and warping the metal. Then you would have bare a bare weld on the side because the rest of the amp is anodized. Now if you had the welding shop fab a clamp to hold the amp that would've been the best way. Either way if he ever sells the amp someone will get a lot of power for cheap. 2001 GMC Sierra Build. Body dropped and Juiced Link to comment Share on other sites More sharing options...
CleanSierra Posted January 4, 2013 Report Share Posted January 4, 2013 The OP hasn't revisited this thread since posting the video. It was posted for ONE intended purpose: to cause utter pandemonium. MISSION=SUCCESS Im not the one you want to try to troll. Just a fyi for you. Link to comment Share on other sites More sharing options...
mbdblue Posted January 4, 2013 Report Share Posted January 4, 2013 Taking it to a welding shop probably would be worse than the hole. There is a lot of heat applied and you have a chance at ruining the board and warping the metal. Then you would have bare a bare weld on the side because the rest of the amp is anodized. Now if you had the welding shop fab a clamp to hold the amp that would've been the best way. Either way if he ever sells the amp someone will get a lot of power for cheap. you can clearly see in the video that these mounting plates simply bolt to the ends of the amp.....he could have easily unbolted it and taking just the plate to a shop leaving the amp behind...and any good welder shouldn't have to apply enough heat to warp the metal. AA-Atomic-Clif Designs-DC-Diamond-Digital Designs-Directed-Eclipse-Fi-Hertz-Hifonics-Kenwood-Memphis-Phoenix Gold-Pioneer-PPI-PSi-Stinger-Sundown-TC Sounds-Viper-Zapco Link to comment Share on other sites More sharing options...
HatersGonnaHate Posted January 4, 2013 Report Share Posted January 4, 2013 The OP hasn't revisited this thread since posting the video. It was posted for ONE intended purpose: to cause utter pandemonium. MISSION=SUCCESS Did it for the monetizable views from YouTube. My name is AdamThis is my Civic Build.7" Samsung Tab 2Kenwood KDC-X896Clarion EQS746Sundown X-15DC 3.5k @2ohmHatersGonnaHate's 02 Civic UBLELD Bypass for Honda Civic/Accord/FitDon's Jeep Grand Cherokee Rebuild N8ball2013 - i think you'd stick your dick in a blender if it told you it was 40 wtih two kids your age. lol srp365 - If posting were picking up bitches, I'd be going home single tonight looks like tony montana sneezed in your car. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.