Sinosic Posted March 31, 2009 Report Posted March 31, 2009 i spread the glue to insure max bond. picture of the port bend after the truckbed liner and port painted. needs a sub..... i just happen to have a 18" sub that forevrbumpn made for me that needed a home sub and enclosure in back of my explorer. alittle over 8 cuft after displacements tuned @ 31hz the amp i will be using is a modded mtx 1501d @ 1ohm whatcha think? Idyllic Enclosures, Pat Quote [email protected]
pstone11 Posted March 31, 2009 Report Posted March 31, 2009 I think it's beautiful. Nice job man! Quote Check out StoneSounds to see my recent builds.Or look at the Flying White Facebook Page!
BASS14 Posted March 31, 2009 Report Posted March 31, 2009 niice! looks tight! Quote Vehicle-2014 Ford Fusion on 20" cruiser alloy obsessionsSubs-4 8" sundown audio E8v3 Sub Amp-Hifonics Brutus Elite 1200.1box-2.8cubes after all dis tuned to 32hz 4" aeroMids and highs-2 sets of Memphis PR 6.5 components Mids amp-Hifonics Brutus Elite 800.4 Deck-Factory IntegrationWiring-Memphis40sqft of damplifier Pro http://www.youtube.c...14?feature=mheeSMD SUPER BUYER/SELLER
indytrucks Posted March 31, 2009 Report Posted March 31, 2009 (edited) I take it you haven't fired it up yet then? Looks damn good Edited March 31, 2009 by indytrucks Quote
Zade08 Posted March 31, 2009 Report Posted March 31, 2009 Great lookin box man. I was suppose to kerf the port on my last box but chickened out at the last minute. Good job mang. Quote Vehicle: 2001 Ford Escape Head Unit: Kenwood Kdc-x592 All out for a rebuild. New shit coming in the next 30 days.
trainman0978 Posted April 1, 2009 Report Posted April 1, 2009 (edited) Looks Damn nice, especially the paint finish. I like it. If you wanna get those "ribs" out of your kerf bend, cut them just a little less shallow, maybe a 1/16 " or so, and double the amount of kerf cuts in the bend. Well.... double may be a little too much , so maybe lets say you made 15 cuts, try it with 21 or 22 .... but it looks cool . Just a thought. I havent made a kerf cut in Mdf, especially not that tall, but when I did interior trim carpentry, we ran into that problem quite often. I would think the same rules apply. Edited April 1, 2009 by trainman0978 Quote 2007 Toyota FJ Cruiser Voo Doo Blue my upgrades and "build" thread. My Kulicki Box Build -Alpine 9887 head unit, KTX-100EQ imprint-( sound quality for dummies! ). - MB Quartz 3.5" in back pillars -Sundown Audio SAX100.4 - JL Audio 3 way 6.5" component set XR653-CSi ( doors and dash ) -JL Audio 2 way Component set XR650CSi - Alpine MRD - M1005 - Alpine Type - R 12" subs -- 2 - 12" s in a Pete kulicki designed box. -Alpine High speed Ipod cable, and KCA-SC100 with Sirius sat. radio -All wiring is Stinger 12 gauge and HPM Level 3 RCAs, KnuKonceptz Kolossus Power and ground and Big done in 1/0, -270 sq. ft. of Damplifier Pro, 36 sq. ft. of Overkill Pro, 6 full sheets of Luxury Liner, and a gallon of spectrum- -2 Powermaster D680 Powercells in back FINALLY !!! I GOT IT METERED ON THE TERMLAB !!! I did a 140.2 at 42 hertz. Shoehorn, BFH, forklift,duct tape and some zip ties
Torres Posted April 1, 2009 Report Posted April 1, 2009 box looks VERY nice! how do you measure the port for tuning in kerfs? i know people do it differently, but do you measure to the end? or halfway? or...? i would like to try a kerf cut, but it might sit better with me knowing the exact tuning frequency of a straight port Quote
uhoh_45 Posted April 1, 2009 Report Posted April 1, 2009 that blue paint is soooooo sexy damn cant wait for some videos Quote R.I.P! (Nov-29-2009) 92 explorer - 4 Atomic Apxx 15s duel .7s - 4rth order bandpass wall -4 powerbass XA-3000D's - 16 8volt batts wired to 16 volts - (9+/9-) runs 0gauge - 152.3 Db @ 29hz BUILD LOG current build 97 chevy lumina4 - 1 Atomic Apx 18 - 6 cube slot port trunk sealed off - 1 powerbass XA-3000D - 2 optima G31s in spare tire18 1 run 1/0 lumina build log
RamenNoodles Posted April 1, 2009 Report Posted April 1, 2009 Looks awesome dude! Quote Diablo Audio Technologies Fi Car Audio Ascendant Audio
wL<3bass Posted April 1, 2009 Report Posted April 1, 2009 Nice looking box you have there sir! Quote Vehicle: 1997 S10 Blazer 4dr 4X4 Exterior: Rear End Bagged, Black Grill, Lifted 2" Amplifiers: Rockford Fosgate T8004 & T10001bd Batteries: 2 Stinger SPV35, Kinetik HC2400 Electrical: Big 3, DC Power 290amp Alternator w/ MLA at 15.5v Enclosure: 4.2 ft³ @ 33Hz 84sq.in. of port (20sq.in. per cube) Headunit: Eclipse CD3200 w/ 80G iPod Mids/Highs: Rockford T152s (a-pillars), Rockford T162s (doors) Subwoofers: 1 15" Fi BL Fully Loaded Wire: All 1/0g Kicker Hyperflex My YouTube Videos My Fiberglass A-Pillar Build My "Seamless" Looking Box Build My DD1508 T-Line Bandpass Build "Seamless" w/ Acrylic Windows (for '05 TrailBlazer) My Stealth 8" Fiberglass Build (for '05 TrailBlazer) My Build For A Friend's '08 Cobalt 15" BL Sealed Off From The Trunk My feedback/references...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.