Leaderboard

you do realize by saying no vs threads you're rentamodding? so you're breaking the rules too, besides this isn't a vs thread, it's not x brand against y brand, it's 2 sundown subs, he's asking which would suit his application better. To the OP, i'd run the SA-8v2 over the SD any day.

I had similar issues with my chevy avalanche 06. Finally broke down and got a alternator from singer that bypasses the PCM control,and I couldn't be happier,I haven't even noticed the voltage dropping below 14 at all. Got a rf 2500 on 3 fi 15sp4. 2xs battery . Before my lights would dim and voltage would drop into 11 sometimes 10.

New amps are pure sex back there

So much sexiness in just a few photos

Not that they're too mainstream, just was under the impression that they'd fallen off since the Blue Thunder of the '90s.

Send me a 2tb hard drive and I will fill it full for you and mail it back. latest greatest complete sets for MAME, NES,SNES, N64 and more I was trying to complete a Hyperspin install check this out

Certified=1674 un-certified=1986 Dynamic=2200

All those small things add up to...... holy fuck there is a shit ton to do. BTW, I found another box of shit Will pulled from the van. You might be missing a 80a relay

I completely underestimated MTX.

a few were closer than you but they BUSTED (please see original post). i think you are the winner of the shirt. No loot though since it wasn't exact. Please contact me @ [email protected] and we will get that out to you! thanks for playing everyone!! it was fun!

An amp with bent tabs would not ship from us that way. We un-package, test, examine, and re-package each amplifier (and every subwoofer / speaker for that matter). It's not impossible for a tab to be bent in transit despite the foam end caps. A drop off the belt in the FedEx warehouse can do so; if dropped on the corner can bend the tab without permanent damage to the packing. We've shipped 1000s of amps over the years and a bend or ding on a corner is the most common sort of damage; packing has been upgraded numerous times over the years but it still happens on occasion. Granted it is very rare with the newest packing. The only way to rectify the bent tab is DIY fix or shipping damage claim and swap it again. Yes it is inconvenient but that is the reality of shipping products. Bottom line, though, is that it would never have left here after inspection with a bent tab. We have full time employees dedicated to JUST QC checking products before they ship; which in and of itself is a rarity in the business these days.

Just wanted to take a minute to describe some of the differences between the AD-1 Amplifier Dyno and the AMM-1 Audio Multimeter The AD-1 Amplifier Dyno can do these things that the AMM-1 cannot do: 1. Measure Amplifier Output into a purely resistive load bank 2. Measure Amplifier Output until 1.0% THD is reached 3. Measure Amplifier Output into 10 different load impedances with the touch of a button 4. Measure Amplifier Dynamic Power Output (IEC-202 Standard for headroom) 5. Capture the exact B+ Voltage that was seen at the amplifier at the moment the last power reading was made 6. Two DD-1+ built in. 7. Measure amplifier output in car using resistive load bank vs your speakers, this provides VERY consistent measurements so the effects from changing things like a better B+ power cable, better ground, better battery etc can be easily and accurately measured This is the exact type of testing the the factories use when manufacturing the amplifiers, and meet CEA standards. They are very defined tests with strict rules. --------------------------------------------------------------------------------------------------------------------------------------------- The AMM-1 Audio Multimeter can do these things that the AD-1 cannot do: 1. Measure amplifier power into your speaker load, both apparent power (VA) and true power (Watts) 2. Measure impedance of your speaker load at any freq from 20Hz - 1kHz 3. Measure the current vs voltage phase shift of a reactive load (Power Factor) 4. Measure the DC Voltages like a multimeter 5. Super fast DC Min/Max for measuring drops and peaks of a DC voltage 6. Measure the Power CONSUMPTION of AC powered devices, like microwaves and light bulbs for example 7. Find the tuning freq of your subwoofer box, box rise and such That is a short summary, I'll be checking when I can to answer any technical questions about the product. Thanks! Tony D