fyerbyrd22

yes, i tried many different variations back there...headunit was set flat the whole time as well, no additional EQ in the vehicle

i was setting gains and filters on Tuesday for 4 sub amps...each pair was strapped, then gain matched..used the dd-1 to find which would be the masters, checked vac and set to the lowest amp...lowest amp was already set clean at 57.2vac so i used that amp as 1 master, and set another amp to match with the cc1...checked vac, and the one amp was 57.2vac and the other was 58.4vac...not enough to make a difference really, but still inaccurate nonetheless, even tho the SMD meters say it was correct then i used the cc1 to set filters..no problems with the lowpass but it would not work on the subsonic...it did read signal but would always say that i needed to go lower (tried 28hz and 35hz i believe) even tho i was all the way down...whatever, left both master amps all the way down on subsonic then went to use amm-1 and it wont read live power..tony told me it needed an update but it would still read tones, not music...tried music, tried tones, and nothing worked any feedback on this would be GREAT..spent alot of money on these tools to have ease of use, over using my scope and so far, they have not been worth it the slightest...is it something that i am doing wrong?

then the agm was bad...mixing agm with lithium helps, not hurts...unless the agm is already shit

never had issues in the past 10yrs with them until last year...received multiple wrong items, missing items, site being wrong about what harness goes with what, etc...ive spent north of $10k with them and they always go in and see that when i bitch...still causes headaches and makes me want to go somewhere else because my last 4-5 orders have all had something wrong, be it not in stock, arriving later than expected (causing me to cancel installation appointments), not shipping out for several days...they have gone downhill noticeably in the past year

Philadelphia phillies

i know for a fact i did it on my opti6k before i got rid of it and i think i did my taramps too

u havent attempted using it on a brazilian amp?...im pretty sure (i dont remember 100% honestly) i tried it on my taramps and it always showed clipping, same thing with my opti6k...i couldnt get any signal on the deck without distortion light on...it was a first run one tho and i heard some had issues...got me a dso nano and everything worked fine

so why dont these work on brazilians?

use uvc2000 in your resin and your resin will dry in like 5min in the sun...then use sonus matter body filler...quickest, lightest filler out..blows away rage gold...will LITERALLY cut your time working on those doors down to a fraction with that combination..with those specific pods, u could make like 5 sets in a day

entered!

entered!

wow, that turned out amazing

3cu per 12?!

i kno this is a revival from the dead but its still useful...whats the specs on the box??...im doin 2 of the sa10 on 3k so this is right up my alley

it shuld tho bc i had the gain set VERY low bc of a small 40a fuse under the hood i didnt wanna pop...so u figure it was doing at most 500w, not including where i set the gain so it wuldnt pop...and yes, i do understand that fuses dont always pop at the rated load and thats its usually double, but even then, it still would be at MOST 1k, again, not including where i set the gain...it was honestly at about 1/8...the kenwood has 2v preouts as well...thats why im saying, it could have just been my ears when i did it...i was gettin demos all day from 156db trucks and cars at the meet

mayb its just my ears then...i jus didnt think the 1500 was louder when it should have been noticeably louder compared to where i set the gain on the 1k

http://www.vminnovations.com/ImageViewer_16149/index.html?guid=1c5cc2d549a0470783c4f01a68192743 and i was supposed to turn the LPF all the way up, NOT the bass boost frequency??...i have the bass boost at 0

just a sub amp for now...no mids/highs amp...i just thought it would go higher than 27, maybe its just me...and i did check the 1000hz and 40hz signal to get my 27 on volume...so is it sub level all the way up, bass at "0"??...im still trying to learn EXACTLY how to use the DD-1

no bass knob...so i can just turn the subwoofer all the way up AND the bass all the way up, then set my gains?

well which is the "correct" spot to set it at?

maybe its just me but when it comes to different headunits, im confused on where to keep the bass settings, subwoofer settings, etc...for example, i just swapped my gfs apsm-1300 (1k but i had the gain VERY low bc of a 40a fuse under the hood) for a apsm-1500 (1.5k, added a new fuse and wiring), i used the DD-1 to set her headunit and amp and i thought i did it correct...im pretty sure tho, that something is wrong bc the headunit started to clip, according to the DD-1 at 27 out of 35 on the headunit (kenwood kdc-448u) and im not sure if it louder...i have the subwoofer all the way up (+13) and the bass at 0 (-8 to +8 )....basically, i need to know if i set it right??...also, if we can update and add to this thread for all headunits so users know EXACTLY what setting to use for their specific headunit, that would be much easier for ppl

gotcha...i just spoke to my friend and im gonna do it tmorrow...ill let u guys no wat happens

that was probably my problem then...like i said, im sure it was user error

ill try again later tonite with sub level at +15...but wouldnt that make it so everything WASNT flat tho??