soundstream15 Posted June 8, 2013 Report Share Posted June 8, 2013 I know the amps make a humming noise when tuning but I retuned my system and when I was backing the gain down for the red distortion light to come off, it did but there was a slight humming. Does that matter since the device was reading clean singal? Quote Link to comment Share on other sites More sharing options...
Kyblack76 Posted June 8, 2013 Report Share Posted June 8, 2013 what amp.. a class D? Quote SMD SUPER SELLER The Burban Build Blazer Build sold Acura trunk build sold Link to comment Share on other sites More sharing options...
soundstream15 Posted June 8, 2013 Author Report Share Posted June 8, 2013 AQ2200 Quote Link to comment Share on other sites More sharing options...
will77530 Posted June 8, 2013 Report Share Posted June 8, 2013 no Quote Link to comment Share on other sites More sharing options...
OrionStang Posted June 8, 2013 Report Share Posted June 8, 2013 Mines just the opposite, stops humming with the light still on. Quote SMD Super Seller My Feedback Thread Link to comment Share on other sites More sharing options...
soundstream15 Posted June 8, 2013 Author Report Share Posted June 8, 2013 ^strange lol As long as I'm good Quote Link to comment Share on other sites More sharing options...
soundstream15 Posted June 9, 2013 Author Report Share Posted June 9, 2013 Mines just the opposite, stops humming with the light still on. Does that depend on amp? Quote Link to comment Share on other sites More sharing options...
CstrokerV Posted June 11, 2013 Report Share Posted June 11, 2013 mine did that too it would humm with the light on i backed it off till the light went out still humming i turned the car off then back on and the hum was gone Quote my build http://www.stevemeadedesigns.com/board/topic/142505-small-build-log-4-dc-lvl3-10s-tl-update-link-to-rebuild/ http://www.stevemeadedesigns.com/board/topic/154258-rebuild-6-lvl3-12s-update-small-video-nothing-spectacular/ new build http://www.stevemeadedesigns.com/board/topic/188181-03-trailblazer-slow-build-8-dc-lvl3-12-m1-motor-m2-parts/ Link to comment Share on other sites More sharing options...
SnowDrifter Posted June 11, 2013 Report Share Posted June 11, 2013 It's normal Quote ~~~~~~~~SAY NO TO PHOTOBUCKET~~~~~~~~ Snow's DD-1 tracks here: https://www.stevemeadedesigns.com/board/topic/167433-snows-dd-1-tracks/ My take on OFC vs CCA: https://www.stevemeadedesigns.com/board/topic/110381-things-that-piss-you-off-in-the-car-audio-world/?do=findComment&comment=2461444 Link to comment Share on other sites More sharing options...
kickass audio Posted June 12, 2013 Report Share Posted June 12, 2013 My DC 5k has a slight hum to it when I have it just below distortion but if I crank the gain up full blast the humming gets really bad and more of buzzes than hums. My 175.4 doesn't do that but they are different class amps so im sure that affects it too. I wouldn't worry about it really. Quote 2004 GMC Envoy1 XS power S3400 batt under the hood and 4 XS Power D3100's battery installed in the rear by the amps0 gauge power wire from front to backAlpine iva-w205 touchscreen dvd/cd/mp3/ipod/am/fm/gps headunitSundown Audio SAX-200.4 amp for my mids and highs8 gauge speaker wire from amp to woofer270 amp Mechman AltRockford Fosgate T1652-s component speakersRockford Fosgate 3Sixty.2 sound processorRca's from Rockford Fosgate and Monster Cable14 gauge speaker wire for the mids and highs1 18" Ascendant Audio SMD Dual 1 ohm with custom Black & Blue carbon fiber and hand signed dustcapBox: 5.66 cubic feet net volume box tuned to 30.13Hz with 1.5" wide wooden dowels and 1.5" thick baffle1 DC Audio 5.0k amp wired to .5 ohms nominal with an imp rise of 1.35 ohms for the single AA SMD 18"Future Vision 8000k 50w bi-xenon projector HID's with 4300k 35w fog lightsLink to my build: Buildupdates/progress Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.