moh.vze.com

www.12vtools.com

duck got the hammer then never came back iirc

 Lol. Why did duck get the Hammer? He was an awesome dude.

You wont notice any difference, your talking maybe 0.001 difference in voltage if even that.

why don't you make a post? this section is for status updates.  

Get the Smd one just got my 4 fuse one yesterday

The ones im talking about arent skyhigh, unless theyre rebranded? But the ones i have are super heavy, u can see them on my battery on my recent pic posts of my trunk on the charger.

These ones look interesting

https://droppinhzcaraudio.com/jims-machineworx-flat-5-lug-bolt-style-battery-terminal-pair/

but I need the ones where the battery mount is in the middle because I have a XS Power clamp down bar for my battery that might short out the terminals.

Toolmaker had these similar ones too but again it's hard for me to connect things without shorting out:

https://toolmakermetalworkz-com.myshopify.com/collections/frontpage/products/aluminum-5-lug-battery-terminals

Here's the middle bar clamp down I'm talking about:

Oh ok i get what ur saying now, yah jims dont have any like that with a center bolt location. Unless you go with the setscrew type, they have those like this. But id prefer the bolt down with ring terminal style too.

https://droppinhzcaraudio.com/jims-machineworx-sae-top-post-8-1-0-gauge-battery-terminal-pair/

i just hook up a DMM to the amp, play a tone where i want my SSF/ISF at and turn it till i start to see a voltage change then bring it just a teeny bit back. same works for LPF. 

I'm going out in the garage now to double check and do attempt #2 with setting the gains and SSF. I probably did have the SSF turned the wrong way yesterday. I want it all the way to 10Hz when I'm tuning not 40 Hz. 

Gonna go redo everytihng and will post up a vid later. I'll probably still get the DD-1+ and CC-1 just to have it in my collection of crap that I own ~_~. I have a clamp meter collecting dust in my closet. 

alright I just finished retuning attempt #2 my subs. Made a thread here: 

Can't decide where it starts clipping on my oscope. I will definitely make a video comparison once I purchase the DD-1+ and CC-1. Oscopes are confusing as hell and I have an Associates of Science in Electrical Engineering ~_~

Gave up on seagate years ago, been using samsung ssd's for quite a while now and love em.

@beaker This is what it sounds like and I think what it's doing (this is not my video):

You might want to try getting another controller board that matches the drive, or flashing the firmware.  That might actually fix it . . . maybe.

Usually you dont want to play any lower than 1/2 octave below tuning.

So if your tuned at 35hz, 1 octave lower would be 17.5hz so that would make a 1/2 octave at 26.25hz.

Typically 5-10hz below tuning, but it will vary depending on power, enclosure size, the size of the port, etc.

Love my DD-1+ and CC-1.  I am constantly changing around settings on my 4 channels for fun to change the sound slightly depending.  Love making adjustments to my sub amps using different overlaps dialed in by 0.1 at a time.  =)  

I think you would be safe going to 28 Infrasonic

Thanks for the input guys! I'm trying to see if I can get the best out of my XLM2's before I change my subs later this year. Came across an interesting video here: 

P.S. This is not a vs post. 

Definitely not 6k in that video... That sub isnt even moving being freeaired. No where near its linear excursion or even peak since the surrounds are not even being dimpled.
Must be a SSL or Power Acoustik 6k amp thats really 1500 watts rms. LOL

Agreed 

Hmm Interesting. I'll probably upgrade this Summer. Hopefully the price doesn't get jacked up

As a result, my left door has a speaker grill attached and my right door has no speaker grill. Fucking shit.

Have you tried installing your left side grill on the right side to see if the right would fit on the left?  Sometimes swapping parts helps.  

Otherwise, you could reach out to HAT and see if they help you out

I listened to it and he goes hard. Like, if you were to just listen to the song without watching the video or seeing who he is it wouldn't be taken as a joke.

#bassheadproblems

yes sir he sure does

https://www.facebook.com/DirtFloorCustoms/

Thats an old page, started as a joke when I was told I couldnt do it years ago. Finally made a legit page after becoming legit and doing it full-time now.
Got somethings planned but gotta get a few other things in check prior. Wont say my ideas because I know how those biters are out there
New page. https://www.facebook.com/AudiofanaticzLLC/

Autoshop owner said he needed 2 days when I dropped my car off. I called on second day 1 hour before closing and he said he needed more time and will give me a call tomorrow morning. So... is it normal for them to not give me updates ahead of time if they needed more time? I thought it was weird that I had to call them instead of them calling me with the updates.

If its a small independent like mine if you are busy you tend to lose track of who needs to be called. I dont have  multiple "service writers"  that can sit and just make calls all day like you would get at a dealer. He may have lost track and forgot to call.   

It's a small shop and he's had it since 1981. I think the business is mainly ran by him and his son (early thirties) and a few older mechanic guys. Last time I was there I can see his three year old grandson chillin at the front desk with them. I pretty much just showed up and payed the bill and shook his hand and said thanks for working on my car.

I asked him how was it working on the Camry and he noted that there were a lot of water everywhere when he did the valve gasket changing. He also asked me if I did my own oil change because he noticed there was something down the oil pan area that needs replacement (probably needs a new washer for the bolt).

Overall, he was a man of very few words but my instincts tell me he does good work when he needs to complete any given task and he's not afraid to keep the car for a couple more days to make sure it gets done right.

My co-worker was the one that recommended the shop and also let me know that the old mechanic owner there is just and old grumpy guy but does good work (he had 3 cars done there).

Also, I tried to ask the old guy if it would be possible to get dual alternators going in my Camry with custom brackets and he kinda refused that job request lol. Dude didn't even recommend any other shops that might be able to do it ( I guess it's not that common to have dual alts in a Camry).

@Kyblack76

the number of the beast

this one? 

or this one, lol

Terrible.