-
Posts
10293 -
Joined
-
Last visited
-
Days Won
22
Content Type
Profiles
Forums
Events
Media Demo
Store
Collections
Videos
Everything posted by MrSkippyJ
-
gotcha. as long as we are on the subject, I have a single pair of RCAs on the input side of my 3sixty. I could not think of any reason to use more than one pair. I have no rear fill, just front stage and sub stage. Can you think of any reason to run a second pair? I could run a sub output from my H/U but with the 3sixty there doesn't seem to be much of a reason too.
-
So there is no need for me to be using a splitter on my sub amp?
-
Yeah, I knew how that part worked too. I was just curious how the monoblock amp treated the inputs.
-
well, i don't have my car atm, it's in a shop being fixed. but even with that, how would I be able to tell what voltage the amp is receiving? I know the RCA outs on the 3sixty are 5v so the sub out would also be 5v. When you split RCAs for 2 amps, you divide the voltage. What is confusing is this is being split to a single amp. Assuming I had L/R sub outs that were 5v you would assume that each L/R input of the amp gets 5v. They way I have to do it is I split a single 5v signal, but to the same amp. Again, I know it doesn't really matter, I'm just curious. got some ninja responses. Thanks guys Ok so they are parallelled internally. Makes sense now. I knew that I had plenty of source voltage, I just wasn't sure how it worked.
-
How does a monoblock amp use the inputs? Most monoblocks have a L/R and of course most sub outputs are mono. My 3sixty has a single sub output, but my amp has the normal L/R inputs. I obviously use a Y-splitter to take care of this, but my question is am I only getting 1/2 my RCA voltage to my sub amp? I know it doesn't really make a difference I just didn't know the answer and it is one of those things that I wanted to know.
-
Not sure if that is enough port area, not a port math person myself. It does look like your port stays the same width (3") after it bends into your enclosure. If that is the case, you need to fix that.
- 12 replies
-
- port
- turbulence
- (and 4 more)
-
Nice use of space, even if the math of the box may not work out. Get that part solved and you seem like you have some decent wood working skills and some creativity too. Not a bad combination! You have a good attitude too, that will help you learn a ton about this audio stuff we love so much, especially on this site with tons of knowledgable people!
-
easiest is to run to the main battery then use the main batteries terminal for a common connection point between battery bank and alternator.
-
If you had.....
MrSkippyJ replied to Mehrl38's topic in General Audio - Can't find a category for your question? Ask here.
i like multiple drivers. so i would do 2 12s. actually, i DID do 2 12s. -
you can do that just as easily with a standard ported enclosure as with a bandpass.
-
I need to seal it off behind my seats what do you mean by that? you can seal off any enclosure.
-
why exactly are you not just going to use a standard ported box? maybe that can help someone figure out a box for you
-
That´s exactly my thoughts!!! Using this same topic i do have a question for you, i have 2 runs of positive and negative wires, what about if i use one positive from my mechman alt to the primary battery and use the other one from the alt directly to the amplifier? just a dumb question lol that would be a lot of work for very little, if any, gain.
-
Wrong. Where are you coming up with this??? I doubt you have ever seen a dual 1 ohm sub playing music at 1/3 ohm, or a dual 2 playing at .6-.7 if you actually paid attention to this whole thread you would see that i got that from his first post were it stated the actual resistance of the voice coil(2 ohm version=1.27 ohms actual) and does it really friggen matter if ive seen a sub playing with that low of resistance i think not, doesnt matter who you are but running an amp that low is can cause overheating and eventual death of the amp not to mention very inefficient and .635 ohms is a lot safer than running .325 Measure the DC resistance of any 2ohm coil and it probably says something similar. If you (or whoever the OP is) wants .5 at the amp, get a D1 sub. It is as simple as that.
-
If you want .5 ohms get the d1 option. That simple.
-
it's too bad you don't have a video of the subs playing, so we can see how much they are or are not moving. I agree with Noob up there that if it sounds good then why worry. I'm wondering though that if this is a matter of your interpretation of how much the subs should be moving or something that is keeping the subs from moving. That is quite a bit of power for those subs and if they aren't moving because of some error then they aren't being cooled either. I'm kinda guessing they just don't move as much as you thought they would.
-
Body filler adds no strength. It's good for finishing purposes not structural purposes.
-
Sausage or Bacon?
MrSkippyJ replied to SnowDrifter's topic in Off Topic - Random, Misc posts - the forum "Junk Drawer"
is this a joke? bacon. what else would you pick?
